manualshive.com logo in svg

TIYA 65050, Operator'S Manual, Page: 19 / 22

Share
Download
TIYA 65050 Operator'S Manual Download Page 19

TABLE SAW

19

GB

TROUBLE SHOOTING

Problem

Cause

Remedy

Motor does not 
start

1.     Fastening nut tightened 

insufficiently

2.   Extension cable defect

3.   Connections on the motor or 

switch defect

1.     Check the mains fuse
2.   Check the extension cable
3.   Have it checked by an electrician

No Motor 
output turns off 
automatically

1.     Overload by dull saw blade

2.   Thermoprotection is triggered

1.     Insert a sharpened saw blade
2.    Motor can be turned on again after 

the cooling period.

Excess vibration

1.     Blade is out of balance

2.   Blade is damaged

3.   Saw is not mounted securely

4.   Work surface is uneven

5.   Blade is warped

1.     Replace the blade
2.   Replace the blade
3.   Tighten all the hardware
4.   Reposition on flat surface
5.   Replace the blade

Cutting binds or 
burns work

1.     Blade is dull

2.   Work is fed too fast

3.   RIp fence is misaligned

4.   Wood is warped

1.     Replace t or Sharpen blade
2.   Slow the feed rate
3.   Align the rip fence
4.   Replace the wood. Always cut with 

convex side to table surface.

Wood edges away 
from rip fence when 
ripping

Rip fence is misaglined

Check and adjust the rip fence

Height/bevel 
adjusting handwheel 
is hard to turn

Gears or screw post inside 
cabinet are clogged with saw 
dust

Clean the gears or screw post

Saw does not make 
accurate 90° or 45° 
cuts

Miter gauge is misaligned (Miter 
Cuts)

Adjust the miter gauge

65050UK00M100.indd   19

2020/5/27   9:36:19

Summary of Contents for 65050























Reviews:

No comments