TIYA 65050 Operator'S Manual Download Page 18 | Manualshive

Page: 18 / 22

TIYA 65050 Operator'S Manual Download Page 18

TABLE SAW

18

GB

8. Remove the riving knife by loosening the

clamp bolt in the clamping plate by turning
it clockwise a few revolutions and then
pulling the riving knife up and out. See
below illustration 4.

9. Attach the ring spanner to the fixing nut.

See below illustration 5.

10. Fasten the drive shaft with the saw blade

key. See below illustration 5.

11. Turn the fixing nut in an anti-clockwise

direction using the ring spanner.

12. Carefully hold the saw blade with one hand

and remove the fixing nut and the outer saw
blade flange from the drive shaft. See below
illustration 6.

13. Now take the saw blade off of the drive

shaft and carefully pull it up and out of the
saw table. See below illustration 6.

16. Place the outer saw blade flange back on

the drive shaft. At the same time, make sure
that the outer saw blade flange is correctly
aligned.

17. Tighten the fixing nut to the drive shaft by

hand.

18. Carefully turn the saw blade in the direction

of rotation: It must be exactly centred
and must not “wobble”. Check the correct
positioning of the saw blade and outer saw
blade flange and adjust the parts again if
the saw blade is not precisely centred.

19. Attached the ring spanner to the fixing nut

and hold the drive shaft with saw blade key.
Turn the fixing nut with ring spanner in a
clockwise direction.

20. Mount the riving knife, the bench insert and

the saw blade guard.

14. Clean the outer and inner saw blade flange

thoroughly before mounting a new saw
blade.

15. Mount a new saw blade on the drive shaft.

Pay attention to the rotational
direction: The cutting interface of
the teeth must be in the direction
of rotation (forwards). Usually, the
direction of rotation is indicated on
the saw blade.

Store the equipment and accessories in a dark
and dry place at above freezing temperature.
The ideal storage temperature is between 5
and 30°C. Store the electric tool in its original
packaging. Cover the electric tool in order to
protect it from dust and moisture.

STORAGE

6

Fixing Nut

Drive Shaft

Blade Flange

5

Ring Spanner

Saw Blade Key

4

65050UK00M100.indd 18

2020/5/27 9:36:19

«
...
16
17
18
19
20
...
»

Summary of Contents for 65050























Reviews:

No comments