TITANTIG 200 DC PULSE PRO Page 20 Operating Manual Download | Manualshive

Page: 20 / 48

background image

TitanTIG 200 DC Pulse

Pro

Operators Manual

Issue. A 0516

1.4 Important notes before use

▲

Do not operate or install this equipment without thoroughly reading this manual and the safety
precautions contained throughout.



Save this manual and keep it handy for reference.



Disconnect mains of the semi-automatic welding machine after finishing work or before a long break.

▲

DO NOT make any modifications to the machine. It may cause changes in the features and
deterioration of technical data.

▲

Any adaptations to this machine are prohibited and may void the warranty.

▲

Warranty is void if any damage to the machine is caused by misuse.



Acceptable range of ambient temperature is from 10—40°C.



Acceptable range of humidity is 20°C at 95% humidity.



Specifications may change without previous notice.

▲

Fitted for commissioning

▲

Recommended outlet

▲

Important Note on TitanTig
200 DC Input Power Supply

This  unit  has  been  supplied  with
a  downgraded  15  Amp  primary
supply  plug  for  commissioning
purposes only. You are advised to
upgrade  the  input  power  plug
and lead to a minimum of 32A if
sustained  usage  at  maximum
amperage is desired.

▲

WARNING

With the    15A plug supplied it is
recommended  that  the  operator
does  not  exceed  more  than
180Amps,  as  use  of  higher
amperages over this amount may
lead to failure and overheating of
the  15A  plug  and  circuit,  which
may  result  in  electrical  supply
component

damage

and

ultimately electrical fires.

«
...
18
19
20
21
22
...
»

Summary of Contents for 200 DC PULSE PRO

















































Reviews:

No comments

Related manuals for 200 DC PULSE PRO

Brand: Elkron Pages: 12

Brand: Fender Pages: 3

Brand: L-Acoustics Pages: 98

APPELLO A105NAX

Brand: E2S Pages: 10

Brand: Onkyo Pages: 10

UTILITY UTAC13-0

Brand: WIA Pages: 8

Brand: Vonyx Pages: 16

Brand: Cal-Royal Pages: 2

Brand: EAW Pages: 2

Brand: Q Acoustics Pages: 32

Brand: MartinLogan Pages: 12

Brand: Omnitronic Pages: 28

Brand: Monitor Pages: 14

Brand: Kemppi Pages: 31

Brand: Eclipse Pages: 6

Brand: Ravaglioli Pages: 68

Brand: Genie Pages: 44

Brand: Omnitronic Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands