Assembly Section 2-22
ASSEMBLY
Run tractor at normal operating RPM to adjust the settings as follows.
Set the dead band compensation potentiometer first.
Set the dead band compensation potentiometer at 50%, or halfway between full
clockwise and full counter-clockwise.
Setting Signal Adaptation Potentiometers:
Disconnect the Deutsch connectors from the actuators of the valve. Use a Volt/Ohm meter to
measure signal voltage and adjust the signal adaptation potentiometers as needed. Pin #4 is
tractor supply voltage. Pin #1 is signal voltage from the joystick, and pin #3 is ground. First
measure supply voltage between pins 4 and 3. Then measure signal voltage between pins 1
and 3 while indexing the joystick function fully in both the “A” and “B” port direction. Divide the
signal voltage by the supply voltage to get signal voltage as a % of supply voltage. This
percentage should not be less than 25% or greater than 75% for the Main Boom, Secondary
Boom, or Swivel function. This percentage should not be less than 30% or greater than 62% for
the Deck Roll function. Note these initial settings for the Deck Roll function should prevent the
spool from shifting into float.
After making this first adjustment to deck roll if the spool still goes
into float, adjust the “B” port screw additionally counterclockwise.
Reconnect Deutsch connectors on control cables to actuators on Danfoss valve. Run
tractor until hydraulic system is at operating temperature. Now refine the adjustments
of the signal adaptation potentiometers for both “A” and “B” ports for all proportional
functions to achieve the following function times. Note: turning potentiometer
clockwise increases the flow or the function speed, and turning them counter-
clockwise decreases the flow or the function speed. Note, if during this procedure the
trim potentiometer is set to full “counterclockwise” but the function is still too fast, use
the mechanical stops at the manual actuator end of the valve section to further limit
flow. Turn limit screw in or clockwise to limit flow. The upper limit screw limits flow to
“B-port”, and the lower limit screw limits flow to “A-port”. However DO NOT adjust the
limit screw on “B-port” of deck roll function. Limiting “B-port” will prevent “float”
function.
Summary of Contents for JD 5083E
