6
TRANSMITTER CONTROLS
1. Transmitter Antenna:
Straighten up the antenna before operating the model.
2. Battery Level Indicator:
Three LEDs indicate the battery voltage level. If the Red LED flashes, please replace the batteries.
3. HI/LO Throttle ATV (Adjustable Travel Volume):
Allows you to independently preset the maximum travel of the throttle servo either side
(high / low) of neutral.
4. Servo reversing switches:
To reverse the servo's rotation direction at the flip of the switch. The reversing switches are recessed into the
transmitter to prevent accidental operation.
5. Steering Trim:
To adjust the steering in small increments or decrements to run the model straight.
6. Throttle Trim:
To adjust the throttle in small increments or decrements and shift neutral position.
7. Steering D/R (Dual Rates):
Push this lever left or right to adjust the amount of the steering dual rate. Right to increase dual rate amount,
and left to decrease amount.
8. AUX Ch Button:
Additional function for controlling of the model.
9. External Charging Jack:
For rechargeable NiCd/NiMH battery pack (transmitter pack only).
10. 2.4GHz binding SW:
The Binding SW button is located on the back of the 2.4GHz transmitter. For additional details, please refer to the
“Binding” setting procedure (Page 5).
11. Steering Wheel:
To control the steering of the model.
12. Power Switch:
Slide to turn the transmitter on & off.
13. Throttle Trigger:
Pull or push to control forward, reverse & speed of the model.
14. Steering Tension Adjustment:
Use a Phillip type screwdriver to tighten or loosen the tension of the steering wheel.
15. Battery Cover:
Slide cover to install or remove batteries.
1.
發射機天線：
使用發射機時，請先將發射機天線打直，以增加訊號接收距離。
2.
發射機電源顯示燈：
三顆
LED
設計顯示發射機電池殘量，若紅色
LED
燈閃爍時，請更換發射機電池。
3.
高、低速油門行程調整鈕：
獨立調整高、低速油門行程量功能。
4.
正逆轉設定裝置：
位於發射機背面（如圖示），控制伺服機作動方向。
5.
轉向微調鈕：
利用此旋鈕，調整設定轉向正確中立點位置。
6.
油門微調鈕：
利用此旋鈕，調整設定油門正確中立點位置。
7.
轉向大小動調整鈕：
調整轉向伺服機的行程量。
8.
第三動開關：
第三動功能開關鈕。
9.
充電孔：
使用充電式電池時，可利用此充電孔，進行充電工作。
10. 2.4GHz
校頻配對設定鈕：
BINDING SW
校頻配對設定鈕為配對發射
/
接收頻率之用。更多設定請參考說明書第
5
頁“安全校頻配對步驟”。
11.
轉向舵輪：
控制車輛轉向裝置。
12.
電源開關：
發射機電源開關。
13.
油門控制板機：
控制車輛前進或後退的裝置。
14.
轉向舵輪調整螺絲：
使用小型十字起子調整此調整螺絲來改變轉向舵輪旋轉鬆緊度。
15.
電池蓋
。
發射機各部功能簡介
4.2 MODEL WIRING DIAGRAM
電控系統連結圖
RECEIVER
接收機
CH1
插槽1
CH3
插槽3
CH2
插槽2
BATT
電池插槽1
THROTTLE SERVO
油門動伺服機
STEERING SERVO
轉向動伺服機
AUX SERVO
預備動伺服機
4.8V~6V RX
BATTERY PACK
4.8V~6V 充電電池包
Summary of Contents for EB-4 S2.5 6242-F
Page 17: ...16 SET UP 22...
Page 20: ...19 REAR ASSEMBLY PD08 0017 PD1924 PD1981 W PD1924 PD1981 W PD1244 PD0560 T 1...
Page 31: ...JD8524...
