Thunder Laser MARS-160 Installation And Operation Manual Download

Page: 78 / 78

THUNDER LASER

MARS-160

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Tel :(86)769 82665376

High pressure air compressor

High pressure air compressor is used for blowing air to reduce material burning.

Note: After two hours of continuous work of air compressors, and it will needs to stop

working for half an hour or more.

----------------------------------------------------------------------------------------------------------------------

Air compressor filter

When we use the High pressure air compressor for blowing air, it will absorb much

moisture with air at the same time. If we just let the moisture go, they will gather on the

focus lens, and when the laser working, the water (moisture) will heat that may lead the

lens break. Thus we need a water separator for help, it can stop moisture reaching lens.

Water separator was installed between the air compressor and laser head.

For how to connect and use the High pressure air compressor set, please refer to below

lesson:

http://www.thunderlaser.com/technical-support/downloads/category/others.html

If you have any question, please contact with us

: [email protected]

THE END

Summary of Contents for MARS-160















































































Search results

Summary of Contents for MARS-160

Reviews:

Related manuals for MARS-160

Brands by name

Popular brands

Thunder Laser MARS-160, Installation And Operation Manual

Search results

Summary of Contents for MARS-160

Reviews:

Related manuals for MARS-160

Brands by name

Popular brands