manualshive.com logo in svg

THORLABS TLD001, Kinesis User Manual

Share
Download
THORLABS TLD001 Kinesis User Manual Download Page 47

Rev A Nov 2017

Page 44

Chapter 6

Software Reference

6.2.4 Advanced Tab 

Fig. 6.4 Laser Driver Settings Panel - Advanced Tab

In order to ensure correct readings during operation, the Photo Diode operating range

must be set before the laser diode is 

Input Source Settings

 - the source(s) which control the output from the laser unit:

If 

Software 

is  selected,  the u nit  responds  to  software  commands a nd  the

output  to  the  laser  is  that se t  using  the  SetPowerSetpoint  method,  or  the

‘OUTPUT’ control on the GUI panel.
If 

External (SMA)

 is selected, the unit responds to the analog signal on the rear

panel EXT IN SMC connector (0 to 10V).
If 

Potentiometer

 is selected, the output to the laser is the value set using the

top panel OUTPUT potentiometer.

Display Intensity

 - determines the brightness of the control panel display.

Enter a value from 0 to 255.

Note

It is possible to select all, or a combination of sources; the sum of the combination is 

then applied to the unit.  

Summary of Contents for TLD001
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands