manualshive.com logo in svg

THORLABS TLD001, Kinesis User Manual

Share
Download
THORLABS TLD001 Kinesis User Manual Download Page 30

Page 27

17874-D03

T-Cube Laser Diode Driver

Display Brightness

This  parameter  allows  the  display  brightness  to  be

adjusted.

Press the MODE button to edit this parameter, or press the

DISPLAY button to skip to the next parameter.

When the MODE button is  pressed, the display shows a

value  from 0  to  256,  which  represents  the b rightness

setting.

Turn the OUTPUT pot to set the required brightness level.

As  the  number  changes,  the  display  brightness  also

changes  accordingly.  When  the  desired  brightness  is

found, stop.

Press  the DISPLAY bu tton  to re turn  to  the  start  of  the

configuration menu.

Press the DISPLAY button to repeat the cycle, or press and

hold the MODE button for more than 3 seconds to return to

the normal operating mode.

When the unit returns to the normal operating mode, the setup is automatically saved

into  non-volatile  memory a nd  the  corresponding  parameters  will  be a utomatically

loaded when the unit is next powered up. This means that the setup process will not

normally need to be repeated unless a different laser diode is used.

Summary of Contents for TLD001
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands