manualshive.com logo in svg

THORLABS LPS710/M, User Manual, Page: 17 / 70

Share
Download
THORLABS LPS710/M User Manual Download Page 17

17

LPS710E Long Travel Piezo Stage and Controller

3.7.2 Connecting The Hardware

1) Install the software - see Section 3.6.

2) Connect the stage to the Controller unit - see Fig. 3.5

3) Connect the Controller unit to the power supply and switch ‘ON’ by pressing the

POWER button on the front panel.

4) Using the USB cable provided, connect the Controller unit to your PC. 

5) Windows

TM

 should detect the new hardware. Wait while Windows

TM

 installs the

drivers for the new hardware - see the Getting Started guide for more information

6) Run the APTUser utility

Start/All Programs/Thorlabs/APT/APT User.

Warning

Piezo actuators are driven by high voltages. Voltages up to 150V may be present 

at the rear panel connector.  This is hazardous and can cause serious injury.  

Appropriate care should be taken when using this device.

Persons using the device must understand the hazards associated with 

using high voltages and the steps necessary to avoid risk of electrical 

shock. 

The piezo controller must be switched OFF before the piezo stage is 

plugged in or unplugged. Failure to switch the controller off may result in 

damage to either the controller, the stage or both.

Caution

The controller and piezo stage are calibrated at the factory and are sold as a

matched pair. The matched pair can be identified by the serial number label

that appears on both units.
Unsatisfactory  performance  is  likely  to  result  if  the  stage  is  driven  by  a

different controller, or if the controller is used to drive other stages.

Note

Ensure that the mating faces of the connectors are properly aligned. 

Misalignment can cause connection problems.

Tighten the securing screws to ensure that the connectors to not  become 

disconnected during use. 

Note

The USB cable should be no more than 3 metres in length. Communication 

lengths in excess of 3 metres can be achieved by using a powered USB hub).

Summary of Contents for LPS710/M







































































Reviews:

No comments