background image

Electronic Variable Optical Attenuators

 

Chapter 7: Regulatory 

Page 14 

 

TTN095737-D02 

Chapter 7  Regulatory 

As required by the WEEE (Waste Electrical and Electronic Equipment 
Directive) of the European Community and the corresponding national laws, 
Thorlabs offers all end users in the EC the possibility to return “end of life” 
units without incurring disposal charges. 

This offer is valid for Thorlabs electrical and electronic equipment: 

 

Sold after August 13, 2005  

  Marked correspondingly with the crossed out 

“wheelie bin” logo (see right) 

 

Sold to a company or institute within the EC  

  Currently owned by a company or institute 

within the EC  

  Still complete, not disassembled and not 

contaminated 

As the WEEE directive applies to self contained 
operational electrical and electronic products, this end of 
life take back service does not refer to other Thorlabs products, such as: 

 

Pure OEM products, that means assemblies to be built into a unit by 
the user (e.g. OEM laser driver cards)  

 Components 

 

 

Mechanics and optics  

 

Left over parts of units disassembled by the user (PCB’s, housings 
etc.).   

If you wish to return a Thorlabs unit for waste recovery, please contact 
Thorlabs or your nearest dealer for further information. 

Waste Treatment is Your Own Responsibility 

If you do not return an “end of life” unit to Thorlabs, you must hand it to a 
company specialized in waste recovery. Do not dispose of the unit in a litter 
bin or at a public waste disposal site. 

Ecological Background 

It is well known that WEEE pollutes the environment by releasing toxic 
products during decomposition. The aim of the European RoHS directive is to 
reduce the content of toxic substances in electronic products in the future. 

The intent of the WEEE directive is to enforce the recycling of WEEE. A 
controlled recycling of end of life products will thereby avoid negative impacts 
on the environment.  

Wheelie Bin Logo 

Summary of Contents for EVOA1550A



















Reviews: