THORLABS BBD102 User Manual Download Page 70

Page: 70 / 76

Appendix D

HA0216T Rev D March 2012

StopCtrl

Stops the ActiveX Control (stops communication
with controller)

StopImmediate

Stops a motor move immediately.

StopProfiled

Stops a motor move in a profiled (decelleration)
manner.

GetDCCurrentLoopParams

Gets the Current servo loop PID parameter settings
applied when the unit is moving

GetDCPositionLoopParams

Gets the Position servo loop PID parameter settings

GetDCMotorOutputParams

Gets the limits that are applied to the motor drive
signal

GetDCTrackSettleParams

Gets the settings for the Track and Settle windows

GetDCProfileModeParams

Gets the settings for the profile mode

GetDCJoystickParams

Gets the settings for the joystick max velocity and
acceleration

GetDCSettledCurrentLoopParams

Gets the Current servo loop PID parameter settings
applied when the unit is ‘settled’.

SetDCCurrentLoopParams

Sets the Current servo loop PID parameter values
applied when the unit is moving

SetDCPositionLoopParams

Sets the Position servo loop PID parameter values

SetDCMotorOutputParams

Sets the limits that are applied to the motor drive
signal

SetDCTrackSettleParams

Sets the parameters for the Track and Settle
windows

SetDCProfileModeParams

Sets the parameters for the profile mode

SetDCJoystickParams

Sets the values for the joystick max velocity and
acceleration

SetDCSettledCurrentLoopParams

Sets the Current servo loop PID parameter settings
applied when the unit is ‘settled’.

Properties

APTHelp

Specifies the help file that will be accessed when the
user presses the F1 key. If APTHelp is set to 'True',
the main server helpfile MG17Base will be launched.

DisplayMode

Allows the display mode of the virtual display panel
to be set/read.

HWSerialNum

specifies the serial number of the hardware unit to
be associated with an ActiveX control instance.

Summary of Contents for BBD102













































































Search results

Summary of Contents for BBD102

Reviews:

Related manuals for BBD102

Brands by name

Popular brands

THORLABS BBD102, User Manual

Search results

Summary of Contents for BBD102

Reviews:

Related manuals for BBD102

Brands by name

Popular brands