2021-04
Accessories
Remarks: Installation information is found in the Instructions for Use, which are enclosed with the accessory. If the copy
of the Instructions for Use is missing, you can download one from www.thomashilfen.de. The assembly / disassembly of
the accessories is done with standard tools.
Leg separator plate (Fig. 32)
The leg separator plate is attached to the rearmost element of the articulating arm, where the saddle is fitted. Fit the leg
separator plate either to the front or rear of the two locating holes in the rearmost element of the articulating arm. The
saddle must be removed before the leg separator plate can be attached. Push the leg separator plate into one of the
locating holes in the articulating arm from beneath. Secure the leg separator plate using the nut. Refit the saddle to the
tGo.
Seat-brake system (Fig. 33)
To install the seat-brake system, the standard rear wheels have to be replaced with the rear wheels with integrated seat-
brake system (available as accessories).This should only be done by a specialist dealer. In order to do so, the hexagon
screw that connects the frame of the tGo to each wheel has to be removed (Fig. 34). Now the standard wheels can be
replaced by the wheels with integrated seat-brake system. Ensure that the suspension is perpendicular to the floor during
installation (Fig. 35). Mount the wheels on the frame of the tGo using the hexagon screws.
If the weight of the child being fitted is very low, a spring may have to be removed from the seat-brake system.
In order to do so, remove the two Allen head screws from the wheel. Set the cap aside, remove one of the metal pins
and pull off the spring. (Fig. 36). Set the pin back into the fixture without the spring. Ensure that the spring of the other
pin is under tension in the recess. Position the cap with the round side facing down and screw it down tight. Before us-
ing, ensure that the screws are firmly tightened.
Return stop (Fig. 37)
To install the return stop, the standard rear wheels have to be replaced with the rear wheels with integrated return stop
(available as accessories). This should only be done by a specialist dealer. In order to do so, the hexagon screw that con-
nects the frame of the tGo to each wheel has to be removed (Fig. 38). Now the standard wheels can be replaced by the
wheels with integrated return stop. Install the wheels so that the plastic curve (Fig. 39) faces to the left respectively. In-
sert the smaller metal spacer sleeves in this side. Install the wheel on the other side with the larger metal spacer sleeves
(Fig. 35). Mount the wheels on the frame of the tGo using the hexagon screws. Before using, ensure that the screws are
firmly tightened.
Vertical handles (Fig. 40)
To install the vertical handles, the standard handlebars have to be replaced. On one side of the handlebars, remove the
foam cover by pulling it off the standard handlebars. (Fig. 41) Remove the small plastic screw on the handlebar adapter
using a screwdriver (Fig. 42) and set the screw aside. Remove the steering tube by guiding the side without the foam
cover through the ring in the handlebar adapter. Loosen the hexagon screw on one of the horns. Remove the horn and
slide the handlebars through the ring in the handlebar adapter so that the screw of the handlebar adapter faces away
from the tGo (Fig. 43). Retighten the screw on the handlebar adapter. Slide the horn onto the handlebars so that the
mounting screw faces away from the tGo and tighten it (Fig. 44). Before using, ensure that the screws are firmly tight-
ened.
Pull rod (Fig. 45)
The pull rod can be hooked into the plastic eye on the tGo frame when needed. (Fig. 45)
Instructions for Use –
t
Go
24
Summary of Contents for tGo
Page 1: ...tGo Instructions for Use tGo Gait Trainer Gebrauchsanweisung tGo Gehtrainer...
Page 2: ...1 2 3 7 8 9 10 11 12 4 5 6 tGo 2021 04 2...
Page 3: ...13 14 15 16 17 18 22 23 24 19 20 21 tGo 2021 04 3...
Page 4: ...tGo 34 35 36 31 32 33 28 29 30 25 26 27 2021 04 4...
