69
68
5. SPECIFICATIONS
5.2 PERFORMANCE SPECIFICATIONS
Hydraulics
Pump Type ................................................................................................. Gear
Pump Brand ..................................................................................... Sundstrand
Pump Displacement, cc (cu. in.) ......................................................... 17 (1.03)
Pump Capacity, (theoretical) lpm (gpm) ..................................... 50.61 (13.37)
Shaker Motor Type .................................................................................... Gear
Shaker Motor Brand ........................................................................ Sundstrand
Shaker Motor Displacement, cc (cu. in.) ............................................ 38 (2.31)
System Relief, bar (psi) @ zero flow .............................................. 204 (3000)
Control Valve(s), 2........................................... 1 Double Spool, 1 Single Spool
Cylinders, inches, .......................................................................................qty 2
Bore Dia. x Stroke x Rod Dia. ..........................Front Jack: 2 x 26 x 1.125
Bore Dia. x Stroke x Rod Dia. ..................Axle Lift: 2.5 x 13.375 x 1.125
Oil Cooler, kJ / m (Btu / m) ............................................................... 448 (425)
Filtration ............................................................... 5 Micron, Spin on Cartridge
Oil Type ............................................................. 10W30, API Classification SJ
Speeds
Engine (Hi idle) ....................................................................................... 2925*
Engine (Low idle) ...................................................................................... 1500
Shaker Shaft, + / - 25 rpm ......................................................................... 1150
*Engine rpm adjusted to set shaker speed. Actual engine rpm may vary.
Engine
Make / Model .............................................................................. Kubota, D905
Type ..................................................... Vertical, Water Cooled, 4 Cycle Diesel
Number of Cylinders ....................................................................................... 3
Displacement, cc (cu.in.) ................................................................ 899 (54.80)
ISO Net Horsepower @3000 rpm, kW (hp) ....................................... 13 (17.4)
Torque @ 2000 rpm, Nm (lbs./ ft) .................................................... 41 (30.34)
Fuel Type ......................................................... Diesel No. 2 -D (ASTM D975)
Cold Starting Aide ............................................................................ Glow Plug
Air Filtration ............................................ Dual Dry Cartridge With Precleaner
Oil Type .............................................................10W30, API Classification CF
Electrical
Battery type, (BCI Group)................................................... 12 Volt, Serv 34/78
Battery Capacity ............................................................................... 730 C.C.A
Alternator .............................................................................................. 30 Amp
Starter, kW (hp) .................................................................................... 1.2 (1.6)
Engine Stop Solenoid ............................................................ Energized to Run
Engine Shut Down Protection ..................................... Oil Pressure, Over Heat
Circuit Protection ........................................................ 40 Amp Circuit Breaker
5. SPECIFICATIONS
5.3 FASTENER TORQUE SPECIFICATIONS
The amount of twisting force (torque) on a bolt or screw is normally measured by
the use of a torque wrench. The correct tightening of bolts is one of the most sin-
gularly important operations done when repairing or conducting maintenance on
your unit. The correct torque can eliminate deformation of mating surfaces.
Virtually every bolt and screw on an engine or component has a torque specifica-
tion for correct tightening. It is imperative that the manufacturer's recommendation
be followed for correct tightening sequence and tightness to eliminate problems
created by bolts and screws being too tight or too loose.
S.A.E. Bolt Grade and Recommended Torque Chart
Shakerhead Bolt & Torque
Bolt, Hex 1/2” UNC GR 5 PL / Nut Flexloc 1/2” - 55 ft. lbs.
Bolt, Hex 5/8” UNC GR 5 PL / Nut Flexloc 5/8” - 95 ft. lbs.
Bolt, Hex 3/4” UNC GR 5 PL / Lock Nut 3/4” - 260 ft. lbs.
1 or 2
5
6
8
1/4
5 Ft
7 Ft.
10 Ft.
10.5 Ft.
11 Ft.
DIA
lbs. lbs. lbs. lbs.
lbs.
5/16
9
14
19
22
24
3/8
15
25
34
37
40
7/16
24
40
55
60
65
1/2
37
60
85
92
97
9/16
53
88
120
132
141
5/8
74
120
167
180
192
3/4
120
220
280
286
316
7/8
190
302
440
473
503
1
282
466
660
714
771
RECOMMENDED
FOR COMPETITION
AND CRITICAL USE
S.A.E.
GRADE
Summary of Contents for ProTough 300 Screener
Page 1: ...Owner s Operator s Service and Parts Manual Publication No 52812 September 2005 300 Screener...
Page 7: ...11 2 CONTROLS 10 Engine Controls 2 1 Hydraulic and Axle Controls 2 2...
Page 39: ...75 74 7 WARRANTY INFORMATION Machines Purchased Through Thomas Dealers 7 1...
Page 63: ...123 122 8 4 ELECTRICAL Engine Electrical 8 4 1 Chassis Electrical 8 4 2...
