background image

1.5

    SAFETY WARNING

IMPORTANT

ALWAYS READ THE USER MANUAL BEFORE OPERATION. 

 

PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE

    PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR 
    AREA.

This product must be installed by a qualified professional.
Always operate the equipment as described in the user manual.
A minimum distance of 0.5m must be maintained between the equipment 

   and combustible surface.

The product must always be placed in a well ventilated area.
Always make sure that the equipment is installed securely.
DO NOT stand close to the equipment and stare directly into the LED 

    light  source.

Always disconnect the power supply before attempting and maintenance.
Always make sure that the supporting structure is solid and can support

    the combined weight of the products.

The earth wire must always be connected to the ground.
Do not touch the power cables if your hands are wet.

ATTENTION

 This product left the place of manufacture in perfect condition.  In order

     to maintain this condition and for safe operation, the user must always 
     follow the instructions and safety warnings described in this user manual.

 Avoid shaking or strong impacts to any part of the equipment.
 Make sure that all parts of the equipment are kept clean and free of dust.
 Always make sure that the power connections are connected correct and

     secure.

 If there is any malfunction of the equipment, contact your distributor 

     immediately.

 When transferring the product, it is advisable to use the original 

     packaging in which the product left the factory.

 Shields, lenses or ultraviolet screens shall be changed if they have 

     become damaged to such an extent that their effectiveness is impaired.

 The lamp (LED) shall be changed if it has become damaged or thermally 

     deformed.

 

1 PRODUCT(GENERAL)

4

17

4 USING A DMX512 CONTROLLER

Ar1.d

BLUE  

1

2

 255

CHANNEL   

FUNCTION

VALUE  

3

4

 255

 255

 255

GREEN

 

RED

 

MASTER DIMMER

Arc.2

BLUE  

1

2

 255

CHANNEL   

FUNCTION

VALUE  

3

4

 255

 255

 255

GREEN

 

RED

 

WHITE 

Ar2.d

BLUE  

1

2

 255

CHANNEL   

FUNCTION

VALUE  

3

4

 255

 255

 255

GREEN

 

RED

 

WHITE 

5

 255

MASTER DIMMER

2010.1.15

2010.1.15

Summary of Contents for expolite tourled pro













Reviews: