background image

Installation / Owner’s Manual  16

Safety Instructions

Safety Awareness

Read this manual carefully and understand the contents before you install the refrigerator.

Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows 

the safety alert symbol and identifies the danger of the hazard.  Carefully read the descriptions of these signal words to fully know their 

meanings.  They are for your safety.

WARNING:

  This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much 

property damage.

CAUTION:

  This signal word means a hazard, which if ignored, can cause small personal injury or much property 

damage.

WARNING:

-  This refrigerator is made for use in RV and towable applications, and is correct for camping use.  It is made to operate with, and 

be connected to, multiple energy sources.  Disconnect all energy sources before you remove the refrigerator or do servicing to 

the refrigerator.

-  This refrigerator is not approved for use as a free standing refrigerator.  It is equipped for the use of propane gas only and can 

not be changed to use any other fuels (natural gas, butane, etc.).

-  Incorrect installation, adjustment, alteration, or maintenance of this refrigerator can cause personal injury, property damage, or 

both.

-  Obey the instructions in this manual to install the intake and exhaust vents.

-  Do not install the refrigerator directly on carpet.  Put the refrigerator on a metal or wood panel that extends the full width and 

depth of the refrigerator.

-  Do not allow anything to touch the refrigerator cooling system.

-  Propane gas can ignite and cause an explosion that can result in property damage, personal injury, or death.  Do not smoke or 

create sparks.  Do not use an open flame to examine the propane gas supply line for leaks.  Always use two wrenches to tighten 

or loosen the propane gas supply line connections.

-  Make sure the electrical installation obeys all applicable codes.  See “Certification and Code Requirements” section.

-  Do not bypass or change the refrigerator’s electrical components or features.

-  Do not spray liquids near electrical outlets, connections, or the refrigerator components.  Many liquids are electrically conductive 

and can cause a shock hazard, electrical shorts, and in some cases fire.

-  The refrigerator cooling system is under pressure.  Do not try to repair or to recharge a defective cooling system.

-  The cooling system contains sodium chromate.  The breathing of certain chromium compounds can cause cancer.  The cooling 

system contents can cause severe skin and eye burns, and can ignite and burn with an intense flame.  Do not bend, drop, weld, 

move, drill, puncture, or hit the cooling system.

CAUTION:

-  The rear of the refrigerator has sharp edges and corners.  To prevent cuts or abrasions when working on the refrigerator, use 

caution and wear cut resistant gloves.

Installation Manual

!

!

!

!

Summary of Contents for N604.3





























Reviews: