background image

5/11/2021, JK 

 

 

EU Declaration of Conformity according to directive 2014/34/EU (ATEX) 

 

 

Thermoprobe, Inc. hereby declares the TP7-D and TP9-A products to be in accordance with the following standards 
and directives:  
 
Name and address of Manufacturer 

ThermoProbe, Inc. 
112A Jetport Dr. 
Pearl, MS 39208  USA 
 

Description of Devices 

 

 

TP7-D and TP9-A  
Portable Electronic Thermometers 

 

Ex-Designation   

 

 

 II 1 G     Ex ia IIB T4 Ga

 

 

 
EC-Type Examination Certificate 

 

ITS17ATEX201515X 

 
Notified Body 

 

 

 

Intertek Italia SPA  
Via Guido Miglioli, 2/A 
20063 Cernusco sul Naviglio (MI), Italy 
Identification Number: 2575 
 

 
Auditing body (QAN) 

 

 

Intertek Italia SPA  
Via Guido Miglioli, 2/A 
20063 Cernusco sul Naviglio (MI), Italy 
Identification Number: 2575 

 
Applied Harmonized Standards 

EN 60079-0: 2018 

  

Explosive atmospheres – Part 0: Equipment – General requirements 

EN 60079-11: 2012 

Explosive Atmospheres – Part 11: Equipment Protection by Intrinsic 
Safety ‘i’ 

 
Applied European Directives 

2014/34/EU - Equipment and protective systems intended for use in potentially explosive atmospheres 

 

ThermoProbe

Inc.

 

 
 
 
Luke Bartkiewicz 
President 

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for TP7-D











Reviews: