Thermopatch NL-24 PRO User Manual Download Page 17

17

BACK TO INDEX

For more information about our products and how to contact us, please visit thermopatch.com

6. Technical specifications

6.1 Specifications of the NL-24 Pro 
Energy use at heating up 

  

 

800 Watt/240 Volt  

 

Voltage  

 

 

 

 

230 Volt  

 

Maximum temperature setting 

  

230°C    

Maximum allowed temperature 

 

270°C    

Height, open   

 

 

 

555 mm  

 

Height, closed   

 

 

 

315 mm  

 

Width    

 

 

 

 

225 mm  

 

Depth (with connections) 

 

 

510 mm  

 

Net weight  

 

 

 

 

20 kg    

Size sealing pad  

 

 

 

140 x 140 mm   

Fuses    

 

 

 

 

2 x 4A T (slow)   

A-weighted noise level  

 

 

< 70 dB(A)  

 

Supplied pressure  

 

 

 

< 6 bar   

Work pressure   

 

 

 

4-6 bar  

 

Safety pressure settings (min/max)    

2 / 6 bar  

 

Compressed air use (per cycle, 5 bar)   

2,6 l/cycle  

 

Heat sealing time stepless adjustment  

3 – 60 seconds

7. Transport and storage

7.1 Transport
When the machine needs to be moved, Thermopatch recommends to use the original packaging. 

7.2 Storage
When the machine needs to be stored, Thermopatch recommends to use the original packaging. The 
machine should be stored on a pallet, off the floor, in dry conditions.

Summary of Contents for NL-24 PRO


























Reviews: