Thermomax SA132 Instruction Leaflet Download Page 4

3

2.

FOREWORD

The SA132 Autodialer / QuickDialer is an intelligent device designed to
connect to any security alarm control panel, and it is compatible with any of
the following Thermomax units - SM12, SM UNO, SM DUE, SM QUATTRO,
LCT-2, SMX 100, etc.).  The Autodialer / QuickDialer enables the dialer to call
any phone numbers programmed to it when an emergency occurs.  The
recorded messages played during the phone calls will alert either the
homeowner or a second party to take action.

The Autodialer / QuickDialer can memorize up to 6 telephone numbers of up
to 32 digits each, and you can record emergeny messages of up to 20
seconds on the system to be played during the phone calls.

The Autodialer / QuickDialer can be programmed to call telephone units,
mobile phones, pager and DISA (Direct Inward System Access) facilities.

Features:

Built-in terminal block to connect to the alarm control panel for emergency
alert.

All phone numbers, emergency messages, and settings are stored in Non-
Volatile Memory (NVM) permanently in case of power failure.

Stores up to 6 telephone numbers (T1 - T6) with a maximum of 32 digits
each.

20-second recording time for emergeny messages.

In case of an emergency, press the 

!

 button on the Autodialer /

QuickDialer, which will immediately start dialing the phone numbers for
help.

Detects dial tone, busy tone and ring back tone so as to perform auto dialing
or auto redialing when the line is busy.  Each phone number will be dialed
for a maximum of 9 times.

Alarm memory facility.

Summary of Contents for SA132














Reviews: