Thermomax SA132 Instruction Leaflet Download Page 11

10

ALARM SYSTEM TRIGGER SETTINGS
Upon receiving an input signal from the connected alarm control panel, the
Autodialer / QuickDialer will react accordingly.  For the Autodialer /
QuickDialer to function correctly, it should memorize each zone’s different
alarm system “trigger type” and “trigger duration”.

Alarm system Trigger Type:

Factory Default: 

 = Normal Open / Normal Low

Trigger Duration:

Factory Default: 

 = 10 seconds duration

Durations 

 and 

 are suitable for “pulse triggers”, i.e. magnetic

reed sensors, shock sensors and glass breaking sensors.

For 

 and 

 duration, as long as the alarm control panel has been

disarmed within 10 or 15 seconds respectively, the Autodialer / QuickDialer
will stop operating right away and the alarm memory will be erased (red
LED stays on accordingly).
If you want the settings different from the factory default, do as follows:

        

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   Type

Duration

     (Select one key)

      (Select one key)

If a new trigger occurs while the previous dialing procedure has not been
completed, the Autodialer / QuickDialer will regard it as the same activation.

If the triggered zone remains in its triggered state after the dialing procedure
is completed, the autodialer / QuickDialer will regard it as the same
activation and will not dial the numbers again.  The previous trigger has to
be cleared for at least 2 seconds before another trigger from the same zone
will be regarded as a new activation.

After being triggered 3 times in a row, the Autodialer / QuickDialer will enter
the “sleep mode” for 1 hour, during which it will not accept any more new

triggers.  During the 1-hour period, you may press the 

 key at any time

to reset the alarm memory to zero for the Autodialer / QuickDialer to be on
alert again.

The panic key trigger is not limited by any of the alarm memory facilities

mentioned above.  You may press the 

!

 key at any time to activate the

Autodialer / QuickDialer.

BUTTON

NORMAL OPEN (N.O.)

NORMAL LOW

NORMAL CLOSE (N.C.)

NORMAL HI

TYPE

1

0

BUTTON

0.06

SECONDS

0.2

SECONDS

DURATION

1

2

3

4

10

SECONDS

15

SECONDS

Summary of Contents for SA132














Reviews: