background image

P a g e

 | 

 

18-5-10 

TCH-150 & 460 

PRODUCT WARRANTY: 

 

1.   This warranty is limited to goods purchased and installed in *Australia.  

Twelve (12) Months full warranty on parts and labour by Thermoline Scientific through its 
authorised dealers or service organisations, will repair or at its option replace any part found to 
contain a manufacturing defect in material or workmanship without charge to the purchaser for 
parts, service labour or any necessary shipping or cartage costs for parts only. This warranty 
does not apply to damage caused by accident, misuse, fire, flood, or acts of God. It does not 
apply to damage caused from  failure to properly install, operate or maintain the goods in 
accordance with the printed instructions provided. To obtain prompt warranty and service, 
simply contact Thermoline Scientific. 

 
2.  If warranty service is required, Thermoline Scientific will endeavour to have an authorised 

service organisation carry out the work if there is an available agent, however if it is decided to 
return the equipment to our main workshop then it is the customers responsibility to pay the 
freight cost of this return, Thermoline Scientific, after the repair, will return the goods at our 
cost, to the customer. 

The customer should always contact Thermoline Scientific for approval to return and 
seek advice as to the best and most cost effective method of return. 

 
3. 

*Export Warranty:

 Limited to replacement of 

Parts Only

. Supplied Ex Factory, Australia. This 

warranty does not apply to refrigeration compressor(s), that are not protected by Thermoline 
Scientific factory installed (VFP) Voltage Fluctuation Protection unit. 

 
4. 

Limitation of Liability:

  Except to the extent not permitted by law, Thermoline Scientific 

excludes all warranties, conditions and terms implied by law. If any implied warranty, condition 
or term does exist, Thermoline Scientific’s liability for breach of that implied term is limited, at 
the option of Thermoline Scientific, to replacement or repair of goods or part thereof, or 
payment of the cost of repairing or replacing the goods or any part of the goods. 
The buyer does not have, under any circumstances, any cause of action or right to claim or 
recover from Thermoline Scientific for, or in respect of, any loss or damage of any kind 
whatsoever, caused directly or indirectly by: 

  any defect in material or workmanship of, or any other defect whatsoever in, or unsuitability 

for, any purpose of the goods or any part of the goods; or 

  default or negligence on the part of Thermoline Scientific or of any employee,    

contractor or agent of Thermoline Scientific or of any person for whom 
Thermoline Scientific had legal responsibility relating to the supply, or otherwise 
concerning the goods or any legal part of the goods. 

5. 

The 12 month warranty period starts from

 the date the equipment is supplied. 

When making a claim for repairs under warranty please state the model number 
and serial number. These are printed on the compliance sticker, normally found 
on the front of the cabinet. Our records will show when the cabinet was 
despatched and if the warranty claim is valid. 

 

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for TCH-150























Reviews: