Thermolec DCC-12 Installation Manual Download Page 9

9

LIGHTS CODE

Green 

The charging station is energized.

Green 

The charging station is energized.  

The total load exceeds 80%. If the loads 
exceed 80% for a predetermined period, 
the charging station will be de-energized.

Yellow 

The charging station is not energized. 

The total loads exceed 80%. The resump-
tion time will start when the total load is 
lower than 80%.

Yellow 

The charging station is not energized. 

The total load is lower than 80% and the 
recovery time is in progress. Each flash 
mean two (2) minutes before the resump-
tion of power to the charging station. (ex: 
3 flashes = 6 minutes before power to the 
charging station). During that period, if 
the total load exceeds 80%, the recovery 
time will restart from the beginning.

Red 

Malfunction: 

1) Check all connections and voltage. 
2) Check the DIP switch configuration 
settings. 
3) Check if the current transformers (CT) 
are properly connected and interlocked. 
4) Check if the connection for the current 
transformers are properly connected to 
the PCB electronics. 
5) If the problem persists, send pictures 
of the installation at [email protected]  
and then call 1 (833) 717-1355.

OFF 

No power. Check the power source.

Charging station power supply

1. Put the circuit breaker in the ON position.
2. Check if the electric vehicle supply equipment (EVSE) is powered:

EVSE powered: go to the next step.
EVSE not energized: check the charging station connections.

STEP 7: SECURE AND RE-ENERGIZE

Secure

1. Turn off the power on the DCC.
2. Put the cover back.

Re-energize

1. Supply electrical power to the DCC.

STEP 8: IDENTIFICATION

1. Identify the branch circuit breaker.
2. Register all configuration settings of the charging station in the 

space provided on the cover.

APPLICATION

Electric vehicle recovery time

Following a power cut to the electric vehicle supply equipment (EVSE), 
a 15 minutes’ delay is initiated to monitor the total consumption of the 
electrical system. Power to the vehicle will then be restored if the total 
load consumption is lower than 80% of the main circuit breaker rating.   

Electric vehicle charging time 

It is recommended to schedule the charging vehicle program during 
hours of low electrical consumption to minimize interruptions to the 
electric charging station.

MAINTENANCE

Do not use any cleaning solvents to clean the DCC.

Summary of Contents for DCC-12


















Reviews: