manualshive.com logo in svg

Thermo Orion Star, User Manual

Share
Download
Thermo Orion Star User Manual Download Page 103

Chapter XIV 

Terms and Conditions

General   

Seller hereby offers for sale to the buyer (“Buyer”) the products herein (the 
“Products”) on the express condition that Buyer agrees to accept and be bound 
by the terms and conditions set forth herein .  Any provisions contained in any 
document issued by Buyer are expressly rejected and if the terms and conditions 
in this Agreement differ from the terms of Buyer’s offer, this document shall be 
construed as a counter offer and shall not be effective as an acceptance of Buyer’s 
document .  Buyer’s receipt of Products or Seller’s commencement of the services 
provided hereunder will constitute Buyer’s acceptance of this Agreement . This is 
the complete and exclusive statement of the contract between Seller and Buyer 
with respect to Buyer’s purchase of the Products .  No waiver, consent, modification, 
amendment or change of the terms contained herein shall be binding unless in 
writing and signed by Seller and Buyer .  Seller’s failure to object to terms contained 
in any subsequent communication from Buyer will not be a waiver or modification 
of the terms set forth herein .  All orders are subject to acceptance in writing by an 
authorized representative of Seller .

Warranty

Thermo Electron warranty for Orion products covers failures due to manufacturer’s 
workmanship or material defects from the date of purchase by the user . User should 
return the warranty card to Thermo Electron and retain proof of purchase . Warranty 
is void if product has been abused, misused, or repairs attempted by unauthorized 
persons .

Warranties herein are for product sold/installed by Thermo Electron or 
its authorized dealers.

Any product sold by a U .S . or Canadian distributor must be returned to Thermo 
Electron for any warranty work . Please contact our Technical Service department for 
further information . A Return Authorization Number must be obtained from Thermo 
Electron Technical Service before returning any product for in-warranty repair or 

XIV-1

Orion Star Series Meter

Thermo Electron Corporation

Summary of Contents for Orion Star
















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands