Thermo Scientific Vitrobot Mk IV User Manual Download Page 8

Page: 8 / 38

Chapter |

Introduction

Confidential, limited rights

PN 103261 | Revision D | 23-Oct-2019

User Manual

Page

1.3.2 Instrument Specifications

The Vitrobot is designed and is strictly meant for use in a fume hood exclusively and is to be
operated by trained personnel only. Users of the Vitrobot are required to have basic
knowledge of the vitrification process.

Power supply

Voltage

100 - 240 Vac

50 - 60 Hz

Fuse

6.3 mains fuse (90 - 150 V)

3.15 mains fuse (150 - 260 V)

Full load

0.25 kVA

Conditions of use

Ambient temperature

18 - 25



Storage temperature

- 40 - 70



Relative ambient humidity

lower than 85 % rH, not condensing

Dimensions and connections

Power cable

90 - 250 V, euro female entry

Wiring configuration

2 wires + ground, single phase

Weight

31 kg

Dimensions (h x b x d) in mm

890 x 260 x 413

Footprint in mm

310 x 450

Summary of Contents for Vitrobot Mk IV







































Search results

Summary of Contents for Vitrobot Mk IV

Reviews:

Related manuals for Vitrobot Mk IV

Brands by name

Popular brands

Thermo Scientific Vitrobot Mk IV, User Manual

Search results

Summary of Contents for Vitrobot Mk IV

Reviews:

Related manuals for Vitrobot Mk IV

Brands by name

Popular brands