manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Instruction Manual

Share
Download
Thermo Scientific TZ-32 Zonal Rotor Instruction Manual Download Page 43

Thermo Scientific TZ-32 Zonal Rotor

 Cleaning of Rotor and Septa — 43

 

6. 2. 

Sterilization of Rotor

Sterilize the rotor appropriately following Table 6-1.

Do not autoclave the rotor or sterilize it in boiling water because its material may deteriorate and its strength may decrease.

Sterilize Method

Condition

Rotor

Usable: 

✔

  Not usable: 

✖

Autoclaving

121 °C (1.0 kg / cm²) for 20 min

✖

Boiling

15-30 min

✖

Ultraviolet rays

200-300 nm

✔

Gas

Ethylene oxide

✔

Formaldehyde

✔

Chemical solution

Ethanol (70%)

✔

Hydrogen peroxide (3%)

✔

Formalin

✔

6. 3. 

Inspection of Rotors

Check the rotor as follows after every use.

• 

If the optical adapter/disk is unclean, wipe it with a soft cloth but do not damage it.

• 

Replacements of packings and O-rings are available.

• 

If the rotor appears to be corroded, deformation, cracks or discoloration is observed, do not use the rotor and call 

a Thermo Fisher Scientific authorized sales representative. The rotor may be irreparable depending on the degree 

of corrosion and wear.

Table 11

Sterilization 
methods

Figure 40

Rotor inspection 
points

Summary of Contents for TZ-32 Zonal Rotor





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands