manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Instruction Manual

Share
Download
Thermo Scientific TZ-32 Zonal Rotor Instruction Manual Download Page 33

Thermo Scientific TZ-32 Zonal Rotor

 General Description — 33

 

5. 3. 3.  Spinning

CAUTION 

Never raise the rotor speed to more than 5000 rpm with the rotor not filled with the solution to full extent (less 

than 90%). High speed spinning of the rotor not full of the solution will cause the septa to be damaged. The 

procedure of spinning the zonal rotor depends on the type of ultracentrifuge used with the rotor. For spinning 

the rotor carefully read and follow the instructions given below and in the instruction manual of the centrifuge.

Speed set to 3000 rpm by acceleration High speed spinning

Speed set to 3000 rpm by deceleration

1. Set to ZONAL operation mode from 

panel.

2. Set operating factors for high speed 

spinning.

3. Press the START switch.

1. Close the door.
2. Press the VACUUM switch.
3. Press the START switch.

1. When the timer counts down to “0”, the 

rotor decelerates to 3000 rpm.

2. Press the VACUUM switch.

NOTE 

When it is desired to stop the rotor, 

set to the normal operation mode 
on the panel.

For details on operating from the panel, refer to the instruction manual of the centrifuge.

5. 3. 4.  Injection of gradient solution and sample

1.  Mount the seal assembly.

Depress the three extrusions of the seal assembly by fitting them into the three relief grooves. Then, the guide at 

the end of the seal assembly enters the rotor shaft. Turn the seal assembly clockwise and release it when it touches 

the rubber stopper.

➀

➀

Rubber stopper

Table 7

Operation modes

Figure 28

Mount the seal 
assembly

Summary of Contents for TZ-32 Zonal Rotor





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands