manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Instruction Manual

Share
Download
Thermo Scientific TZ-32 Zonal Rotor Instruction Manual Download Page 20

Thermo Scientific TZ-32 Zonal Rotor

 Rotor Assembly — 20

 

Maximum Speed

The maximum speed of the rotor inscribed on the rotor cover surface is determined using the maximum density of gradient 

solution below 1.2 g/ml.

If the maximum denstity of gradient solution exceeds 1.2 g/ml, decrease the maximum speed of the rotor according to 

the following equation: 

Employed Materials

The following materials are used on the passage of the sample:

Part name

Material

Tygon tube

PVC (specially processed)

Tee

Polypropylene

Metallic section of seal attachment assembly etc.

Stainless steel

Stationary seal surface (seal assembly side)

Tungsten carbide

Rulon seal

Tetrafluorethylene resin (Rulon)

O-Ring

NBR

Rotor, cover, shaft, metal ring

Titanium alloy

Septa

Noryl (polyphenylene oxide resin)

Seal packing

Fluorine rubber

Table 4

Employed materials

Summary of Contents for TZ-32 Zonal Rotor





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands