Thermo Scientific Sorvall ST 8 Instruction Manual Download Page 19

Page: 19 / 67

Introduction and Description

Rotor Selection

Sorvall ST 8 Centrifuge

Thermo Scientific

Rotor Selection

The Thermo Scientific Sorvall ST 8 Centrifuge is supplied without a rotor.

Various rotors are available to choose from.

The technical data of the rotors and the corresponding adapters and reduction sleeves for various
commercially available containers can be found in the corresponding rotor operating manuals.

For more information visit our website at: http://www.thermoscientific.com

Thermo Scientific Rotors

Part No.

TX-150 swinging bucket rotor

75005701

TX-150 round buckets

75005702

TX-150 50mL conical buckets

75005703

TX100S clinical swinging bucket rotor with sealed carriers

75005704

TX100 clinical swinging bucket rotor with carriers

75005705

M10 microplate swinging bucket rotor

75005706

M10 with buckets

75005723

MT12 microtube swinging bucket rotor

75005600

HIGHConic III fixed angle rotor

75005709

CLINIConic fixed angle rotor

75003623

MicroClick 24x2 microtube rotor

75005715

MicroClick 30x2 microtube rotor

75005719

8x8 PCR Strip rotor

75005720

Hematocrit rotor

75005733

Summary of Contents for Sorvall ST 8




































































Search results

Summary of Contents for Sorvall ST 8

Reviews:

Related manuals for Sorvall ST 8

Brands by name

Popular brands

Thermo Scientific Sorvall ST 8, Instruction Manual

Search results

Summary of Contents for Sorvall ST 8

Reviews:

Related manuals for Sorvall ST 8

Brands by name

Popular brands