Thermo Scientific Sorvall ST 8 Instruction Manual Download Page 9

Page: 9 / 67

Preface

Sorvall ST 8 Centrifuge

Thermo Scientific

Symbols used on the centrifuge

Symbols used in the manual

Observe the information contained in the instruction manual to keep yourself and your environment
safe.

This symbol refers to general hazards. Follow the instructions in the instruction manual in
any case.

This symbol refers to biological hazards..

Observe the information contained in the instruction manual to keep yourself and your
environment safe.

This symbol refers to information on hazards, described within the manual.

This symbol refers to disconnect mains before transporting or servicing the centrifuge.

This Symbol refers to check, if the rotor is installed correct by lifting it slightly at the handle.
See

“Rotor Installation”

page 31

This symbol refers to general hazards.

CAUTION means that material damage could occur.

WARNING means that injuries or material damage or contamination could occur.

This symbol refers to biological hazards.

This symbol refers to electrical hazards.

Summary of Contents for Sorvall ST 8




































































Search results

Summary of Contents for Sorvall ST 8

Reviews:

Related manuals for Sorvall ST 8

Brands by name

Popular brands

Thermo Scientific Sorvall ST 8, Instruction Manual

Search results

Summary of Contents for Sorvall ST 8

Reviews:

Related manuals for Sorvall ST 8

Brands by name

Popular brands