Thermo Scientific Sorvall LYNX 4000 Instruction Manual Download Page 44 | Manualshive

Page: 44 / 72

background image

4

Operation

Additional Features

34

Sorvall LYNX 4000 / 6000

Thermo Scientific

Rotor Landing Pad

You can place the rotor on the right hand side of the centrifuge in front of the touchscreen. The surface
is anti-skidding.

Rotor Lid Holder

You can place the rotor lid in the rotor lid holder feature on the left hand side of the centrifuge.

Figure 16.

Auto-Lock Rotor Lid

CAUTION

Do not place anything on the rotor landing pad when the centrifuge door is

closed.

Note

Some rotors lids have a mandrel that is part of the Auto-Lock. Use the rotor lid holder to

store the rotor lid.

CAUTION

Mind the Auto-Lock mandrel inside the rotor lid. Do not touch the mandrel.

«
...
42
43
44
45
46
...
»

Summary of Contents for Sorvall LYNX 4000









































































Reviews:

No comments

Related manuals for Sorvall LYNX 4000

Brand: NEC Pages: 54

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: Bard Pages: 36

Brand: Bard Pages: 2

Brand: Bard Pages: 30

Brand: Bard Peripheral Vascular Pages: 44

Brand: Nautilus Pages: 17

Brand: National Instruments Pages: 6

Brand: Vaisala Pages: 2

INTRA PROPHYwiz 181 P

Brand: KaVo Pages: 22

Brand: Festo Pages: 40

Brand: Neurotech Pages: 24

Brand: Feniex Pages: 5

Brand: Carbatec Pages: 29

Brand: PurAthletics Pages: 2

MERLIN N Series

Brand: Meheen Pages: 24

Brand: Williams Sound Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands