Thermo Scientific Sorvall LYNX 4000 Instruction Manual Download Page 37

Page: 37 / 72

Operation

Rotor Installation

Thermo Scientific

Sorvall LYNX 4000 / 6000

Close Centrifuge Door

1. Close the centrifuge door by pressing down on it lightly in the middle or on both sides of it.

Two locks close the centrifuge door completely.

Rotor Installation

The approved rotors for the Sorvall LYNX 4000 / 6000 centrifuge are listed in section

“Rotor

Selection”

page 7

. Use only the rotors and accessories from this list in the centrifuge.

The rotors are equipped with an Auto-Lock rotor exchange.
This system is used to automatically lock the rotor to the centrifuge spindle. The rotor does not have to
be bolted on to the centrifuge spindle.

1. Open the door of the centrifuge and if necessary remove any dust, foreign objects or residue from

the chamber.
Auto-Lock

and o-ring must be clean and undamaged.

Figure 9.

Auto-Lock Adapter

Note

The door should audibly click into place. Do not slam the centrifuge door.

CAUTION

Do not reach into the gap between the centrifuge door and the housing. The

centrifuge door is drawn shut automatically.
Place you hands always on top of the centrifuge door.

Use the emergency release only for malfunctions and power failures (see

“Manual Door

Release”

page

CAUTION

Unapproved or incorrectly combined accessories can cause serious damage to

the centrifuge.

Auto-Lock Latch

O-Ring

CAUTION

Make sure that the length and width of the tubes are fitting into the adapter and

cavities. Do not use tubes that are too short or too thick for the adapter and the cavities.

Proceed as follows:

Summary of Contents for Sorvall LYNX 4000









































































Search results

Summary of Contents for Sorvall LYNX 4000

Reviews:

Related manuals for Sorvall LYNX 4000

Brands by name

Popular brands

Thermo Scientific Sorvall LYNX 4000, Instruction Manual

Search results

Summary of Contents for Sorvall LYNX 4000

Reviews:

Related manuals for Sorvall LYNX 4000

Brands by name

Popular brands