Thermo Scientific Orion AQUAfast AQ3010 User Manual Download Page 3

Page: 3 / 39

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

Table of Content

ntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

AQ3010 Meter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Unpacking the Meter and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 2

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Keys and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Turbidity Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Calibration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Indexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Calibration Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Preparing and Filling the Calibration Standard Vials . . . . . . . . . . . . . . . . 8

Calibration Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Refilling the Calibration Standard Vials with Fresh Standard . . . . . . . . . 10

Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Restoring Factory Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Turbidity Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Turbidity Measurement Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Preparation of Sample Vial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Measurement Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Single-Shot or Continuous Measurement . . . . . . . . . . . . . . . . . . . . . . 19

Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Vials – Handling, Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Customer Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Notice of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

WEEE Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Chapter 1

Chapter 5

Chapter 4

Chapter 3

Chapter 2

Summary of Contents for Orion AQUAfast AQ3010








































Search results

Summary of Contents for Orion AQUAfast AQ3010

Reviews:

Thermo Scientific Orion AQUAfast AQ3010, User Manual, Page: 3 / 39

Search results

Summary of Contents for Orion AQUAfast AQ3010

Reviews: