manualshive.com logo in svg

Thermo Scientific Orion AQUAfast AQ3010, User Manual, Page: 22 / 39

Share
Download
Thermo Scientific Orion AQUAfast AQ3010 User Manual Download Page 22

1

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

6 .  After the power-up sequence, the meter will go to the measurement 

mode and the display will blink “-Rd-” about ten times .  See  

Figure 12

 .

 

7 .  The measured reading will appear in the display . 

8 .  If necessary, place the second sample vial into the sample well .  Align 

the vial alignment mark with the meter alignment mark . 

9 .  Press the 

READ/ENTER

 key .  The display will blink “-Rd-” several 

times and measured reading will appear . 

10 .  Repeat this procedure for all of your samples .

• 

Never pour liquid directly into the sample well of the instrument

 .  

Always use a 25 mm vial .  The instrument will only accurately 

measure the turbidity of a sample when 25 mm vials sealed with the 

black caps are used .  The black cap serves to both seal the vial and 

block stray light .

•  Never attempt to clean the sample well .  The optics may be damaged .

•  For battery conservation, the instrument automatically powers off 20 

minutes after the last key pressed .

Measurement Notes

Figure 12

Reading a 

Turbidity Value

“-Rd-” flashes about 

10 times

SAMPLE

Unknown 

NTU

Place sample 

vial into the 

sample well 

 

NTU

R EA D

EN TE R

Measurement Mode

 

and cover with
the light shield cover, 
           if needed 

Summary of Contents for Orion AQUAfast AQ3010








































Reviews:

No comments