manualshive.com logo in svg

Thermo Scientific Orion AQUAfast AQ3010, User Manual, Page: 29 / 39

Share
Download
Thermo Scientific Orion AQUAfast AQ3010 User Manual Download Page 29

25

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

Warning: 

 This meter may radiate radio frequency energy and if 

not installed and used properly, that is in strict accordance with 

the manufacturer’s instructions, may cause interference to radio 

communications .  It has been tested and found to comply with the limits 

for a Class A computing device pursuant to Subpart J of Part 15 of FCC 

Rules, which are designed to provide reasonable protection against such 

interference in a commercial environment .  Operation of the meter in a 

residential area may cause interference in which case the user at his own 

expense will be required to take whatever measures may be required to 

correct the interference .

The Thermo Scientific Orion AQ3010 turbidity meter is CE and 

cTUVus certified, which includes TUV 3-in-1 testing to EMC and US 

and Canadian standards .

This product is required to comply with the European Union’s Waste 

Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC .  It 

is marked with the following symbol:

We have contracted with one or more recycling/disposal companies in 

each EU Member State and this product should be disposed of or recycled 

through them .  Further information on compliance with these Directives, 

the recyclers in your country, and information on Thermo Scientific 

Orion products which may assist the detection of substances subject to 

the RoHS Directive are available at www .thermo .com/WEEERoHS .

Notice of 

Compliance

WEEE 

Compliance

Summary of Contents for Orion AQUAfast AQ3010








































Reviews:

No comments