Thermo Scientific Orion AQUAfast AQ3010, User Manual, Page: 21 / 39

Share

Page: 21 / 39

Thermo Scientific Orion AQUAfast AQ3010 User Manual Download Page 21

17

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

1 . Place the AQ3010 turbidity meter on a flat and level surface .

Note:

Do not hold the meter in your hand while operating it, as this may

cause inaccurate measurements .

2 . Place the sample vial inside the sample well and align the vial’s

alignment mark with the meter’s alignment mark . See

Figure 11

.

3 . Push the vial down until it slides fully in .

4 . Cover the vial using the light shield cover, if necessary . For many

environments this is not required . The vial cap seals the sample well .

5 . Turn on the meter by pressing the

ON/OFF

key .

Figure 10

Applying the Silicon Oil

Measurement

Procedure

Figure 11

Aligning the Sample

Vial Alignment Mark

with the Meter

Alignment Mark

Align the alignment
mark on the sample
vial with the
alignment mark on
the AQ3010 turbidity
meter and push until
it is fully snapped in

«
...
19
20
21
22
23
...
»

Summary of Contents for Orion AQUAfast AQ3010








































Reviews:

No comments