Thermo Scientific Orion 2117HL User Manual Download Page 98

Page: 98 / 122

Troubleshooting

VI-15

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Displayed

Event Code

Description

Cause

Troubleshooting

System Event/Error Codes - Yellow LED

E004

DEFAULT VALUES

Analyzer has been reset or is new out
of box

Calibrate the analyzer

E021

HARDWARE FAULT

System error

Contact Technical Support 1-800-225-1480

E101

CH1 TEMP OUT OF RANGE

Temperature sensor on channel 1 out of
range (5 °C to 45 °C) for ISE

Check ATC cable and probe connections. Replace if needed.

E102

CH2 TEMP OUT OF RANGE

Temperature sensor on channel 2 out of
range (5 °C to 45 °C) for ISE

Check ATC cable and probe connections. Replace if needed.

E111

CH1 CAL DUE

User calibration required on channel 1.
No calibration has been performed in
user specified time interval.

Recalibrate the analyzer.

E112

CH2 CAL DUE

User calibration required on channel 2.
No calibration has been performed in
user specified time interval.

Recalibrate the analyzer.

E127

CH1 SOUT mA OVER RANGE

Measured sensor value above Sout high
limit value on channel 1

Verify user selectable Sout high limit value in setup mode

E128

CH1 SOUT mA UNDER RANGE Measured sensor value below Sout low

limit value on channel 1

Verify user selectable Sout low limit value in setup mode

E129

CH1 TOUT mA OVER RANGE

Measured temperature value above Tout
high limit value on channel 1

Verify user selectable Tout high limit value in setup mode

E130

CH1 TOUT mA UNDER RANGE Measured temperature value below Tout

low limit value on channel 1

Verify user selectable Tout low limit value in setup mode

E131

CH2 SOUT mA OVER RANGE

Measured sensor value above Sout high
limit value on channel 2

Verify user selectable Sout high limit value in setup mode

E132

CH2 SOUT mA UNDER RANGE Measured sensor value below Sout low

limit value on channel 2

Verify user selectable Sout low limit value in setup mode

E133

CH2 TOUT mA OVER RANGE

Measured temperature value above Tout
high limit value on channel 2

Verify user selectable Tout high limit value in setup mode

E134

CH2 TOUT mA UNDER RANGE Measured temperature value below Tout

low limit value on channel 2

Verify user selectable Tout low limit value in setup mode

Summary of Contents for Orion 2117HL



























































































































Search results

Summary of Contents for Orion 2117HL

Reviews:

Thermo Scientific Orion 2117HL, User Manual, Page: 98 / 122

Search results

Summary of Contents for Orion 2117HL

Reviews: