manualshive.com logo in svg

Thermo Scientific Orion 2117HL, User Manual, Page: 93 / 122

Share
Download
Thermo Scientific Orion 2117HL User Manual Download Page 93

Troubleshooting

VI-10

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Slope greater than -62 mV/decade

•  Improper calibration technique – refer to 

Chapter IV, Performing a 

DKA Calibration

.

•  Calibration standards contaminated – repeat the calibration using  

fresh standards. 

•  Electronics failure – reset the analyzer. Refer to 

Chapter VI, Resetting 

the Analyzer

.

•  Improper pipet technique – refer to the 

Appendix, Pipet Operation

 

and Technique

 section.

•  Background concentration too high for the standards used.

•  Cables interchanged – verify wiring of cable connections to terminal 

strip. Refer to 

Chapter II, Wiring the Analyzer

.

•  Check the connection of the cable markers for the corresponding 

electrode. Cable markers are the white tape at the cap connector on  

the cable.

•  “Ref” for the reference electrode
•  “Sensing” for the chloride electrode

•   Sensing electrode coated – clean or replace the sensing electrode.

High Slope

Summary of Contents for Orion 2117HL



























































































































Reviews:

No comments