manualshive.com logo in svg

Thermo Scientific Orion 2117HL, User Manual, Page: 33 / 122

Share
Download
Thermo Scientific Orion 2117HL User Manual Download Page 33

Analyzer Operation

III-7

Thermo Scientific Orion 2117HL High Level Chloride Analyzer User Guide

Channel Specific Setup 

Mode Menu Options

If a two channel analyzer is in use, the following setup mode menu options 

are specific to the first channel of the 2117HL analyzer for chloride 

measurements. When a pH/ORP board or conductivity board is installed 

on the second channel of the 2117HL analyzer, refer to the 

Thermo 

Scientific Orion 2100 Series pH/ORP Analyzer and Conductivity Analyzer 

User Guide

 for detailed instructions on the second channel setup mode 

menu options.

The operator must select the channel number in the main setup mode 

(CH1 or CH2) and the menu options that are relative to the measurement 

capability of that channel will be displayed. If a one channel analyzer is 

being used, the CH1 and CH2 menus will not be shown.

Set the number of significant digits, mV display option and concentration 

units displayed when in the measure mode: 
•  Set the number of significant digits displayed measure mode
  •   Scroll through 2, 3 or 4 significant digits
  •   Default significant digits – 3
•  Enable mV values to be displayed on the second line
  •   Scroll between On or OFF
  •   Default mV setting – OFF
•  Set the displayed concentration units
  •   Scroll through AUtO (automatically ranges from ppb to ppm), PPb 

(parts per billion, ppb), or PP (parts per million, ppm) 

  •   Default displayed concentration units – AUtO

Set the time that the system will remain on hold before the actual 

measurements are displayed after a calibration:
•   Once the hold time expires, the system implements any programmed 

changes to settings in the setup mode

•   After a calibration, the hold function allows the operator to rinse the 

electrodes prior to recording actual measurement values

•   Default hold time – 30 minutes

Adjust the temperature reading from the ATC probe by ± 5.0 °C:
•   Default adjustment – 0.0 degrees C

MEAS

CH1 or CH2

HOLD

TADJ

Summary of Contents for Orion 2117HL



























































































































Reviews:

No comments