Thermo Scientific LCQ Fleet Getting Started Manual Download Page 50

Page: 50 / 74

Connecting a Thermo Scientific LC System

Making Contact Closure with a Surveyor Plus LC System

LTQ Series Getting Connected Guide

Thermo Scientific

3. To connect a Surveyor MS Pump or Surveyor MS Pump Plus to the LC/MS interconnect

cable:

a. Connect the end of the adapter cable labeled PUMP to one of the PUMP connectors

of the 7-connector LC/MS interconnect cable.

b. Plug the end of the adapter cable labeled MS PUMP into the 8-pin socket on the rear

panel of the Surveyor MS Pump or Surveyor MS Pump Plus.

Figure 23.

Surveyor Plus LC system connected to an LTQ Series MS detector

+ -

Start In

DETECT

PUMP

A/S

PUMP

MS PUMP

MS Detector

Autosampler

Pump

Detector

7-connector LC/MS interconnect cable

Pump

Detector

Solvent platform

Autosampler
(rear panel)

Surveyor
LC Pump
(rear panel)

Detector
(rear panel)

LTQ Series MS detector
(right-side panel)

LTQ/LXQ

interconnect
adapter cable

Not drawn to scale

Surveyor
MS Pump
(rear panel)

Adapter cable for Surveyor MS Pump
7 in. (18 cm) P/N 60053-63038

To
LC/MS interconnect
cable connector
labeled PUMP

To
Surveyor MS Pump

Connector labeled PUMP

Connector
labeled
MS PUMP

Summary of Contents for LCQ Fleet











































































Search results

Summary of Contents for LCQ Fleet

Reviews:

Related manuals for LCQ Fleet

Brands by name

Popular brands

Thermo Scientific LCQ Fleet, Getting Started Manual

Search results

Summary of Contents for LCQ Fleet

Reviews:

Related manuals for LCQ Fleet

Brands by name

Popular brands