Thermo Scientific Dionex ICS-900 Installation And Quick Start Instructions Download Page 23

Page: 23 / 24

Doc. 065214-02 1/12

Dionex ICS-900 Installation
Checklist



Unpacked the Dionex ICS-900; checked for
damage and verified that all items were
received



Connected the autosampler (if used)



Installed the software, the USB dongle (if
used), and the software license



Connected the USB cable



Connected the power cord



Turned on the power to the PC, the Dionex
ICS-900, and the AS Autosampler (if
installed)



Installed the Dionex ICS-900 device driver



Created a timebase and configured devices



Connected to the Chromeleon panel tabset



Verified that the correct regenerant bottle
assembly was received:

•

For anion analyses, the cap is labeled

ANION

and the

REGEN BOTTLE OUT

line

extends to the bottom of the bottle

•

For cation analyses, the cap is labeled

CATION

and the

REGEN BOTTLE OUT

line

extends only about 1 cm (0.4 in) into the
bottle



Prepared the eluent and regenerant



Connected the bottle lines to the Dionex
ICS-900



Hydrated the suppressor



Set up the waste lines; verified that the black
DCR waste backpressure tubing is installed
on the

REGEN OUT

line



Primed the pump



Flushed the system, guard column, and
separator column



Installed the columns and suppressor



Connected the backpressure coils; verified
that the correct type and number are installed



Filled the regenerant line



Equilibrated the system

Summary of Contents for Dionex ICS-900

























Search results

Summary of Contents for Dionex ICS-900

Reviews:

Related manuals for Dionex ICS-900

Brands by name

Popular brands

Thermo Scientific Dionex ICS-900, Installation And Quick Start Instructions

Search results

Summary of Contents for Dionex ICS-900

Reviews:

Related manuals for Dionex ICS-900

Brands by name

Popular brands