4.2 Installation
1. Connect all the components according
to the figures shown on page 4 of this
manual. Use grounded power outlet.
2. Press the power switch "I" side and
switch on the instrument.
4.3 Settings
Time Settings
1. Continuous mode
Press the “ ” or “ ” arrow button
below the Time/Tilt display window.
When the number shown on the Time/
Tilt display window starts flashing, press
“ ” arrow button to decrease the time
to 00:00 and then release the button. The
time setting is finished after the number
shown on the Time/Tilt display window
flashed twice.
2. Timer mode
Press the “ ” or “ ” arrow button
below the Time/Tilt display window.
When the number shown on the Time/
Tilt display window starts flashing, press
“ ” or “ ” arrow button to increase or
decrease the time value. Release the
button when the time shown on the
Time/Tilt display window reaches the set
value. The time setting is finished after
the number shown on the Time/Tilt
display window flashed twice.
Speed Settings
Press the “ ” or “ ” arrow button
below the Speed display window. When
0100 will show on the Time/Tilt
display window. When the time shown
in between 0100 to 9999, the default
step is 1 minute. 3 seconds after the
rocking time is chosen, the Time/Tilt
display window will flash and the
instrument will automatically take the
value shown as the set rocking time.
Run and Stop
Press “ ” button and the instrument
will start running with the specified
settings and the Run indicator light will
be on.
The Time/Tilt dispaly window will show
the cumulative time (Continuous Mode),
or remaining time (Timer Mode) and the
Speed display window will show the
current speed.
Press “ ” button again and the
instrument will slow down until it stops.
The instrument will then be in standby
and the two display windows will show
the set values.
Finish Operation
After the operation is finished, press the
power switch at the back right side the
instrument and put it into the “O” state.
Unplug the instrument and store the
instrument according to the storage
guide.
Alarm System
Err1: If running speed does not match
the setting speed, the instrument will
have a three-time reboot, and after the
three reboots failed, there will be a
buzzer, and then Err1 will be displayed in
the Speed display window .
End of timer: The instrument buzzing
alarm, the "End" is displayed in the Speed
window.
When the instrument alarms, press any
key, the instrument is back to the
standby mode.
Power Recovery
If the power supply is cut off suddenly
while the instrument is in operation, the
unit will automatically run at the
previously set parameter upon power
restoration. The display windows will
flash. Press any button to stop flashing.
Mechanical Zero Correction
To ensure accurate and quality rocking,
the instrument will automatically run
mechanical zero correction in the
following situations:
1. First operation after the machine is
turned on.
2. First operation after the rocking speed
is reset.
3. After 8 hours of continuous operation.
Run
Stop
Run
Stop
the number shown on the Speed display
window starts flashing, press “ ” or
“ ” arrow button to increase or
decrease the speed value. Release the
button when the speed shown on the
Speed display window reaches the set
value. The speed setting is finished after
the number shown on the Speed display
window has flashed twice.
Note:
press the “ ” or “ ” arrow
button for a longer time to accelerate the
setting.
Tilt Angle Setting
1. Press “ ” button and the Tilt
indicator light will be on.
2. Press the “ ” or “ ” arrow button
below Time/Tilt display window to
choose the tilt needed. The range of
tilt displayed on the window is 1 to
15°. After 3 seconds, the Time/Tilt
display window will flash and the
instrument will automatically take the
value shown as the set tilt.
Rocking Time Settings
1. Press “ ” button and the Time
indicator light will be on.
2. Press the “ ” or “ ” arrow button
below Time/Tilt display window. The
Time/Tilt display window will show the
time value. When the time shown is
between 00:01 to 99:59, the default
step of the instrument when changing
the time is 1 second. Continue to
press “ ” arrow button and the value
Mode
Mode
9
|
Section 4 Operation
Digital Rocker 10
