Thermo King Rail Edition SLXi-DRC Maintenance Manual Download Page 6

Page: 6 / 104

TK 56433-5-MM-EN

Condenser Check Valve
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Bypass Check Valve. . . . . . . . . . . . . . . . . . . . . . 71

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Receiver Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Filter-Drier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Expansion Valve Assembly . . . . . . . . . . . . . . . 72

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Heat Exchanger . . . . . . . . . . . . . . . . . . . . . . . . . 72

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Evaporator Coil Assembly . . . . . . . . . . . . . . . . 73

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Three-Way Valve Repair. . . . . . . . . . . . . . . . . . 74

Removal/Disassembly . . . . . . . . . . . . . . . . 74
End Cap Checks. . . . . . . . . . . . . . . . . . . . . . 75

Check Valve Bleed Hole Diameter . . . . . . 75

Assembly/Installation . . . . . . . . . . . . . . . . 76

Three-Way Valve Condenser Pressure
Bypass Check Valve Repair . . . . . . . . . . . . . . . 77

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Pilot Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Suction Vibrasorber . . . . . . . . . . . . . . . . . . . . . 77

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 78

High Pressure Cutout Switch . . . . . . . . . . . . . 78

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 78

High Pressure Relief Valve. . . . . . . . . . . . . . . . 78

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Discharge Pressure Transducer . . . . . . . . . . . 78

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Suction Pressure Transducer . . . . . . . . . . . . . 78

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Electronic Throttling Valve (ETV) . . . . . . . . . . 79

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Installation of Service Kit . . . . . . . . . . . . . 80
Installation of Complete ETV
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Hot Gas Bypass Valve . . . . . . . . . . . . . . . . . . . . 81

Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Compressors with Internal Oil Filter . . . . . . . 81

Internal Oil Filter Replacement . . . . . . . . 81

Checking Compressor Oil Pressure. . . . . . . . 82

e.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 8

Unit and Engine Mounting Bolts . . . . . . . . . . 84

Unit Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Condenser, Evaporator, and Radiator
Coils. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Micro-Channel Coil Cleaning
Recommendations . . . . . . . . . . . . . . . . . . . 84

Cleaning Intervals . . . . . . . . . . . . . . . . . . . 84
Cleaning Methods . . . . . . . . . . . . . . . . . . . 84

Defrost Drains . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . 85

Defrost Damper . . . . . . . . . . . . . . . . . . . . . . . . . 85

Testing Defrost Damper . . . . . . . . . . . . . . 86
Troubleshooting Defrost
Damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Replacing Damper Gear Motor . . . . . . . . 87

Condenser and Evaporator Fan
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Condenser Inlet Orifice
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Evaporator Fan Blower
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

blle

e o

off C

ntte

nttss

Summary of Contents for Rail Edition SLXi-DRC









































































































Search results

Summary of Contents for Rail Edition SLXi-DRC

Reviews:

Related manuals for Rail Edition SLXi-DRC

Brands by name

Popular brands

Thermo King Rail Edition SLXi-DRC, Maintenance Manual

Search results

Summary of Contents for Rail Edition SLXi-DRC

Reviews:

Related manuals for Rail Edition SLXi-DRC

Brands by name

Popular brands