background image

 

MINI ULTRA ELECTRIC BOILERS Installation and operating manual (Revision: May 2015)                                               

13

 

4.3 OPERATION OF THE INTERFACE  

The  controller  uses  four  push  buttons  at  the  bottom 
of the display to select and adjust the parameters. 
The  button 

is  used  to  access  to  the 

configuration menu and confirm a selection. 

The 

buttons are used to select an 

item or adjust a value.  
The 

button  enables  the  illumination  of  the  display 

under two different modes.  
The  default  mode  will  enable  the  illumination  of  the 
display for a period of 10 sec. each time a button is 

pressed.  If  the 

is  pushed,  the  light  will  be 

continuously  illuminated.  Just  press  the  button  to 
change the mode of activation. 

 

Figure 10 : UltraSmart Control Module

 
4.4 OPERATION IN “FIXED BOILER 
TEMPERATURE SET POINT” 

For  installation  where  the  boiler  target  temperature 
shall  be  maintained  at  a  fixed  temperature  that  will 
not  vary  in  relation  to  the  outdoor  temperature,  the 
sequence of operation will be as follow: 
On  a  call  for  heat  from  the  room  thermostat,  the 
circulating pump will start and the boiler will activate 
the number of stages required to get to and maintain 
the outlet temperature of the boiler near the selected 
target  temperature.  A  rotation  of  the  stages  based 
on an equal time period of operation is provided. 
 
N.B. 
The supplied outdoor temperature sensor shall 
not  be  connected  before  applying  the  electrical 
power to the unit. 

 
4.5 OPERATION WITH “OUTDOOR RESET” 

For  installation  where  the  boiler  target  temperature 
shall 

modulate 

in 

relation 

to 

the 

outdoor 

temperature;  when  the  outdoor  temperature  gets 
colder, the boiler target temperature will increase. 
On  a  call  from  the  room  thermostat,  the  circulating 
pump  will  start  and  the  boiler  will  activate  the 
number of stages required to get to and maintain the 
outlet boiler temperature near the target temperature 
established  by  the  controller  according  to  the 
outdoor temperature. A rotation of the stages based 
on an equal time period of operation is provided.  
N.B. The supplied outdoor temperature sensor must 
be connected before applying the electrical power to 
the unit. 
 

 
The  boiler  target  temperature  will  be  calculated  by 
the controller in relation to the parameters selected 

in  the  menu 

and  the 

maximum  target  temperature  required  when  the 
outdoor  temperature  will  get  to  -10F  (-23C).  The 
“STD”  curve  corresponds  to  the  default  maximum 
temperature  for  a  typical  system  and  this  value  can 
be modified from the “MIN” to “MAX” value shown on 
the following tables. 
 
The  following  tables  show  the  values  of  the  target 
temperature  that  will  be  obtained  in  relation  to  the 
outdoor temperature. 
 

Summary of Contents for MINI ULTRA























Reviews: