background image

 

BTH Electric Boilers USE & CARE MANUAL 

(Revision June.2014)

,                                                                                     Page 

4.

 

INSTALLATION 

 
 
The manufacturer’s warranty does not cover any damage or defect caused by installation, or 
attachment, or use of any special attachment other than those authorized by the manufacturer 
into, onto, or in conjunction with the water heater.  The use of such unauthorized devices may 
shorten the life of the boiler and may endanger life and property.  The manufacturer disclaims any 
responsibility for such loss or injury resulting from the use of such unauthorized devices 

 

LOCATION 

The electric boiler should be installed in a clean, 
dry  location.    Long  hot  water  lines  should  be 
insulated  to  conserve  water  and  energy.    The 
electric  boiler  and  water  lines  should  be 
protected 

from 

exposure 

to 

freezing 

temperature. 
The  electric  boiler  must  be  located  or  protected 
so  as  not  to  be  subject  to  physical  damage,  for 
example, by moving vehicles, area flooding, etc.  

 

 
The  electric  boiler  should  not  be  located  in 
an  area  where  leakage  of  the  tank  or  water 
connections  will  result  in  damage  to  the 
adjacent  area  or  to  lower  floors  of  the 
structure.    When  such  areas  cannot  be 
avoided,  a  suitable  drain  pan  or  non-
flammable  catch  pan,  adequately  drained, 
and  must  be  installed  under  the  boiler.   
The pan must be connected to a drain. 
NOTE:  Auxiliary catch  pan MUST conform to 
local codes. 

 

 
The  boiler  can  be  mounted  directly  on  a  wall 
with  adequate  screws.  It  needs  to  be  properly 
leveled. 
All models in alcoves. The  ambient temperature 
must not exceed 90F (32C) 
The electric boiler should not be located near an 
air vent blowing  a corrosive  atmosphere or high 
humidity.  The limited warranty is void when the 
failure of  the  electric boiler  is due to a corrosive 
atmosphere.

 

The choice of the mounting position of the boiler 
shall  be  made  in  relation  with  the  required 
clearances  shown  below  and  the  fact  that  the 
electric  element  compartment  of  the  boiler 
needs clearance to allow their replacement. 
°

CLEARANCE  

 

For  adequate  inspection  and  servicing  the 
following minimum clearance is necessary: 

Sides 

4 in. /10cm 

 Electric elements side  

14 in./35cm 

Front side of the boiler 

24 in./60cm 

Back  

0 in./0cm 

 

 

Fig. 2 Mounting position

CAUTION 

WARNING 

Summary of Contents for MINI Ultra 12



















Reviews: