background image

 

BTH Electric Boilers USE & CARE MANUAL 

(Revision June 2014)

,                                                                                                     Page 

18

 

 

 

MINI ULTRA

 

 

LIMITED  WARRANTY 

Warranty Coverage for Residential Installation. 

Thermo 2000 Inc. hereby warrants to the original residential purchaser that the MINI 
ULTRA tank installed in a residential setting shall be free of leaks during normal use 
and service for a period of fifteen (15) years from the date of purchase as long as 
the original residential purchaser owns the home in which the unit was originally 
installed. Residential setting shall mean usage in a single-family dwelling in which 
the consumer resides on a permanent basis. Also, residential setting shall mean use 
in multiple family dwellings in which one (1) MINI ULTRA tank is to be used in only 
one (1) dwelling.  In the event that a leak should develop and occur within this 
limited warranty period due to defective material or workmanship, such leak having 
been verified by an authorized company representative, Thermo 2000 inc. will repair 
or replace at our sole discretion the failed unit with the nearest comparable model at 
the time of replacement.  
 

The 

original residential purchaser is responsible for all costs associated with the 

removal and reinstallation, shipping and handling to and from manufacturing plant.  
The replacement unit will be warranted for the remaining portion of the original 
Warranty. 

 

Warranty Coverage for Commercial Installation. 

Thermo 2000 Inc. warrants to the original purchaser that the MINI ULTRA tank 
installed in a commercial setting shall be free of leaks during normal use and service 
for a period of fifteen (15) years from the date of purchase.  
 
Commercial setting shall mean use in other than residential setting stated above in 
the residential setting definition.  In the event that a leak should develop and occur 
within this limited warranty period due to defective material or workmanship, such 
leak having been verified by an authorized company representative, Thermo 2000 
inc. will repair or replace at our sole discretion the failed unit with the nearest 
comparable model at the time of replacement.  

 

The 

original purchaser is responsible for all costs associated with the removal and 

reinstallation, shipping and handling to and from Manufacturer.  The replacement 
unit will be warranted for the remaining portion of the original Warranty. 

 

Limited two years warranty on all MINI ULTRA 
components & parts 

All other MINI ULTRA components & parts are warranted for a period of two (2) 
years against defects due to defective material or workmanship.   

The 

original 

purchaser is responsible for all costs associated with the removal and reinstallation, 
shipping and handling to and from Manufacturer.  The components, repaired or 
replaced are warranted for the residual period of the initial warranty on the unit. 

 
 
 
 

Exclusions 

This warranty is void and shall not apply if: 

1.

 

Defects or malfunctions resulting from installation, repair, maintenance and/or usage 
that are not done in conformity with the manufacturer’s installation manual; or 

2.

 

Defects or malfunctions resulting from installation, maintenance, or repair that are 
not done in accordance with regulations in force; or 

3.

 

Defects or malfunctions resulting from improper installation, maintenance or repair 
done carelessly or resulting from consumer damage (improper maintenance, 
misuse, abuse, accident or alteration); or 

4.

 

Installation in which a relief valve (pressure) is not installed or if it is not functioning 
properly, or when it is not connected to a drain to avoid damage to the property; or 

5.

 

Installation in which liquid circulating in the tank does not remain in closed circuit or 
installation in which piping is leaking; or 

6.

 

A polybutylene pipe or radiant panel installation without an oxygen absorption 
barrier is used; or 

7.

 

Installation where the acidity of water is not within the normal Environmental 
Protection Agency (EPA) (between pH 6.5 – 8.5) guidelines or the domestic water 
contains abnormal levels of particulate matter or water exceeding 10.5 gpg; or 

8.

 

Your home contains any type of water softener system and the unit is not installed 
and maintained in accordance with the manufacturer specifications; or 

9.

 

The MINI ULTRA unit has been subjected to non authorized modifications; or 

10.

 

Defects or malfunction resulting of storing or handling done elsewhere than Thermo 
2000’s manufacturing plant; or 

11.

 

Units on which the serial number is removed or obliterated. 

 

Limitations

 

Thermo 2000 shall not be responsible for any damage, loss, and inconvenience of any 
nature whatsoever, directly or indirectly, relating to the breakdown or malfunction of the 
unit. This warranty limits its beneficiary’s rights. Nevertheless, the beneficiary may have 
other rights, which vary from state to state. 
 
This warranty replaces any other expressed or implicit warranty and constitutes the sole 
obligation of Thermo 2000 towards the consumer.  The warranty does not cover cost of 
removal, reinstallation or shipping to repair or replace the unit, nor administration fees 
incurred by the original consumer purchaser.  
 
Thermo 2000 reserves its rights to make changes in the details of design, construction, or 
material, as in its judgment constitute an improvement of former practices.  
 
This warranty is valid only for installations made within the territorial limits of Canada and 
the United States. 
 

 

Warranty service procedure 

Only authorized MINI ULTRA dealers are permitted to perform warranty obligations.  The 
owner or its contractor must provide Thermo 2000’s head office or authorized depot with 
the defective unit together with the following information:  MINI ULTRA model and serial 
number, copy of the original sales receipt and owner’s identification certificate. 

 

 
 

 

 

 

 

 

THERMO 2OOO INC. 

500, 9e Avenue, Richmond (Qc) Canada J0B 2H0 
phone:  (819) 826-5613   Fax:  (819) 826-6370 
www.thermo2000.com

 

Summary of Contents for MINI Ultra 12



















Reviews: