Thermia Thermia Legend User Manual Download

Page: 15 / 28

5.5

Hot water

The hot water settings are set from factory (or by installer for any installation specific requirements) for high

hot water comfort & availability with high savings efficiency. Therefore no adjustments are required. Automatic

top up (anti-legionella) is with factory setting performed in a one week interval in operating mode Auto.

For special occasions, when maximum availability of hot water is desired, a one-time top up heating "EXTRA

HOT WATER" may be initiated.

To activate, press > select "HOT WATER" and then "EXTRA HOT WATER".

If the operation mode "COMPRESSOR" is set when the function is activated, the top up will be done only on

compressor.

If operation mode Auto is set when the function is activated, both compressor & auxiliary heater will be used to

provide maximum amount of hot water.

Note! The function is only possible to activate when the hot water tank is not already considered as fully charg-

ed by the controller.

5.6

System information

Check applicable operating data described in the tables below. The information can be found in the sub-menu

INFORMATION > TEMPERATURE >

Operating data, temperature

Sensor

Explanation

Outdoor

Shows the temperature on the outdoor sensor.

System supply line

Optional. Depending on system application.

Desired supply line

Shows the calculated requirement value for the supply line.

Hot water

Shows the temperature of the hot water sensor, if hot water production is

permitted.

Supply line (HP)

Shows temperature of outgoing radiator temperature from heat pump.

Return line (HP)

Shows temperature of incoming radiator temperature to heat pump.

Brine in

Shows the current temperature of brine in to the heat pump.

Brine out

Shows the current temperature of brine out from the heat pump.

Operating time

The information can be found in the sub-menu INFORMATION > OPERAT.TIME >

Explanation

COMPRESSOR

Shows the number of hours that the heat pump has been in operation.

AUX. HEAT 1

Shows the number of hours that the immersion heater step 1 has been in

operation.

User Guide

Thermia Legend

Thermia AB

BWLE01UG0102

Summary of Contents for Thermia Legend





























Search results

Summary of Contents for Thermia Legend

Reviews:

Related manuals for Thermia Legend

Brands by name

Popular brands

Thermia Thermia Legend, User Manual

Search results

Summary of Contents for Thermia Legend

Reviews:

Related manuals for Thermia Legend

Brands by name

Popular brands