Thermia Thermia Legend User Manual Download

Page: 23 / 28

Appendix

9.1

Display symbol description

9.1.1

Symbol description

The display shows information about the heat pump’s operation, status and alarms.

Symbols that show the heat pump status:

Symbol

Meaning
COMPRESSOR – Indicates that the compressor is in operation. Flashing = Brine monitoring ac-

tive (Compressor temporarily stopped.)
LIGHTNING BOLT – Indicates that the electrical immersion heater is in operation. The number

indicates which additional step is activated.
HOUSE – Indicates that the heat pump produces heat for the heating system.

TAP – Indicates that the heat pump produces heat for the water heater. A lightning symbol

next to this symbol indicates peak heat charging (anti-legionella function).

FLOW SENSOR – An F indicates that there is sufficient flow. (Only if flow/level guard is connec-

ted.)
TANK – Indicates the level of hot water in the water heater. When hot water is produced, this is

indicated by a flashing icon for the tank.
SQUARE – Either indicates that the operating pressure switch has deployed, or that the pres-

sure pipe temperature has reached its maximum temperature. (Compressor may temporarily

stopped.)
COOLING – Displayed if cooling is produced. A = Active cooling. (Accessory)

The following operating information may also appear:

Message

Meaning

ROOM

Shows the set ROOM value. Standard value: 20°C.

If the room sensor (accessory) is installed it shows the actual temperature, while the

desired indoor temperature is shown in brackets.

START

Indicates that there is a need for heat or hot water production and that the heat

pump will start.

EVU STOP

Indicates that the additional function EVU (Elektrizitätsversorgungsunternehmen) is

active. This means that the heat pump is off as long as EVU is active.

NO HEAT DEMAND

Indicates that there is no demand for heating or hot water production. (Compressor

temporally stopped.)

COMPRESSOR START

--XX MIN

Indicates that there is a need for heat or hot water production and that the heat

pump will start in XX minutes.

User Guide

Thermia Legend

Thermia AB

BWLE01UG0102

Summary of Contents for Thermia Legend





























Search results

Summary of Contents for Thermia Legend

Reviews:

Related manuals for Thermia Legend

Brands by name

Popular brands

Thermia Thermia Legend, User Manual

Search results

Summary of Contents for Thermia Legend

Reviews:

Related manuals for Thermia Legend

Brands by name

Popular brands