background image

Xsase VI LCS

VG4000 Series

This time, don't let Xaser VI slip away !

English

English

23

24

4.1  Toughpower / Purepower / TR2 
        power supply series (optional)

Chapter4  Other

The  Thermaltake  Power  Supply  series  specification  meets  latest  Intel  & 

AMD  dual  &  Quad  core  processors  and  NVIDIA  &  AMD  high  performance 

graphic  cards;  it  offers  plenty  of  functions,  which  mainly  include:

1.  Automatic  Fan  Speed  Control:  All  power  supply  can  detect  the  inside 

     heat  and  automatically  adjust  the  fan  speed  to  provide  adequate  airflow.

2.  Ultra  Silent:  Ball  bearing  fans  with  high  reliability  140mm  or  120mm 

     cooling  fan  and  super  low  acoustic  noise  under  all  load  condition.

3.  Modularized  Cable  Management:  To  eliminate  clutter  and  improve 

     airflow  inside  the  case.

4.  Dedicated  Graphic  Card  Power:  reduce  the  loading  on  current  PSU  and 

     no  need  to  upgrade  current  PSU  while  running  multi  graphic  cards  mode.

The  functions  can  assure  all  Thermaltake  Power  Supply  meets  the  balance 
in  noise  control  and  heat  exhausted.  All  power  supply  provides  complete 
protection  function  as  follow:
1.  Over  power  protection.
2.  Short  circuit  protection  on  all  output.
3.  Over  voltage  protection  /  Under  voltage  protection.
4.  Over  current  protection.
5.  Over  temperature  protection.

Besides,  Thermaltake  enables  the  quality  assurance  of  all  power  supply: 
100%  Hi-POT  and  ATE  Function  Test,  100%  Burn-In  and  AC  Input  cycled 
on/off  under  high  temperature  condition.  Furthermore,  it  has  been  approved 
by 

UL,  CUL,  TUV,  CB,  FCC,  CE,  and  BSMI.

There  are  three  main  products  line  of  Thermaltake  PSU  which  divided  into 
Toughpower,  Purepower  (include  Purepower  RX)  and  TR2  (include  TR2  RX) 
series.  Please  refer  to 

http://www.thermaltake.com/product/Power/power_index.asp

Chapter5
Liquid Cooling Installation

Summary of Contents for VG400LBNS
























Reviews: