Thermador DWHD860RFM, Use And Care Manual

Page: 28 / 84

28
Eco forecast
When Eco forecast is activated, the average water and
energy consumption of the selected wash cycle is briefly
displayed in the digital display
@
.
Auto power off
This setting determines the length of time the control
panel stays illuminated after the cycle is complete.
To save energy, the recommended setting is “after one
minute”.
Possible settings are:
▯
off:
The appliance does not switch off automatically.
▯
After one minute:
The appliance switches off after
1 minute. This is the most energy efficient setting.
▯
After two hours:
The appliance switches off after
2 hours.
Tone volume
The end of the wash cycle is indicated by a buzzer. You
can also change this setting.
Button volume
When you are operating the dishwasher, a signal sounds
whenever a button is pressed. You can control the
volume of the signal. If you do not like the button volume,
you can switch it off.
Greeting
When you switch on the dishwasher, the brand logo
appears. You can switch off the brand logo.
Factory setting
You can reset all settings to the factory setting.
Switching the appliance on
1.
Turn the water supply on fully.
2.
Open the door.
3.
Switch on
On/Off
switch
(
.
The
Auto
wash cycle has been preset as a default
whenever the appliance starts. This wash cycle
remains selected if no other wash cycle button
0
is
pressed.
4.
Press
Start
button
)"
.
5.
Close the door.
Wash cycle sequence starts.
Note:
Your dishwasher is protected against unintentional
operation. If the appliance door remains open for more
than 4 seconds after pressing the Start button, the
operation will be paused. Press the Start button again
and close the appliance door.
Delay start time
You can delay the start of the wash cycle by up to
24 hours. Depending on the setting of the time display,
the end of cycle is indicated with “Finish in” (for example
3h 25m) or “Finish at” (for example 15:20 hours).
1.
Open the door.
2.
Switch on
On/Off
switch
(
.
3.
Select wash cycle
0
.
4.
Press
Delay
start button
`
.
5.
Keep pressing the setting buttons
+ - X
until the
displayed time corresponds with your requirements.
6.
Press
Start
button
)"
, timer programming is
activated.
7.
To delete the Delay start time, press
Start
button
)"
for about 3 seconds.
8.
Close the door.
Note:
Your dishwasher is protected against unintentional
operation. If the appliance door remains open for more
than 4 seconds after pressing the Start button, the
operation will be paused. Press the Start button again
and close the appliance door.
emotionLight
emotionLight
1"
is the interior lighting for your
dishwasher. You can switch the interior lighting on or off.
Once you have switched on emotionLight, you can select
other settings.
Possible settings are:
▯
Emotion Light 1 (brightness setting for interior
lighting)
:
In the setting Emotion Light 1 you can adjust the
brightness of the interior lighting in 4 levels.
▯
Emotion Light 2 (color setting of interior lighting)
:
In the setting Emotion Light 2 you can select a color
for the interior lighting.
▯
Emotion Light 3 (visual signaling of faults)
:
In the setting Emotion Light 3 you can switch the
visual indication of a fault on or off.If you have
switched on Emotion Light 3 and a fault occurs on
your dishwasher, the interior lighting will flash.
Notes
▯
Depending on the setting of
▯
AutoPowerOff
▯
, the interior lighting is either switched on or off.
▯
Note that the interior lighting is automatically switched
off after 1 hour when it is switched on and the door is
open.
▯
When the interior lighting is switched off, the settings
for emotionLight 1 to emotionLight 3 cannot be
selected.