27
Operating the Dishwasher
Note:
With hidden controls, the door must be opened
before changing settings and closed after changing
settings.
9
WARNING
RISK OF INJURY
To avoid risk of injury, always use caution when
opening the door during or following a wash cycle
as hot water or steam may escape. Do not fully
open the door until water noises have stopped and
steam has subsided.
Protection against unintentional operation
Your dishwasher is equipped with a function that helps to
prevent unintentional operation (e.g. by children).
After setting the dishwasher, the dishwasher door has to
be closed within 4 seconds, otherwise the operation will
be paused. There will be a signal on the control panel
advising you to press the Start button again and close
the door.
This function will be activated when:
▯
pressing Start to begin a wash cycle
▯
setting Delay time and pressing Start
▯
opening the door while Delay time is active
▯
opening the door during a wash cycle.
Note:
This function cannot be deactivated.
Operating the touch buttons
Buttons are sensitive and should be touched gently.
Avoid any grease or food particles resting on the buttons
as they could activate the dishwasher.
Wiping and cleaning can also activate the dishwasher.
For best results, use bare, clean hands when touching
the buttons.
To clean the touch buttons wipe them with a dry or
slightly damp cloth.
Changing the settings
The dishwasher has been preset with certain settings for
your convenience. You can change these factory
settings.
Change the setting as follows:
1.
Open the door.
2.
Switch on On/Off button
(
.
3.
Press Info button
8
for 3 seconds until the following
text is indicated in the digital display
@
:
Scroll with
< >
Set with - +
Leave with Setup 3 sec.
4.
Keep pressing button
>
)*
until the required setting
is indicated in the display window at the top
@
.
5.
Make the selection with setting buttons
+ -
X
.
6.
Press and hold the Info button
8
for 3 seconds.
The chosen setting has now been stored.
Tip:
If you change several settings, first make all
changes in succession. Now press the Info button
8
for 3 seconds. This saves all set values in the appliance.
AquaSensor
The AquaSensor is an optical measuring device which
measures the cleanliness of the rinse water.
The AquaSensor is used according to the wash cycle. If
the AquaSensor is active, “clean” rinse water can be
transferred to the next rinse and water consumption can
be reduced by 0.8–1-5 gal (3–6 liters). If the rinse water
is not yet clear, the water is drained and is replaced with
fresh water. In the automatic wash cycles the
temperature and running time can also be adjusted to
the degree of soiling.
Time display
The wash cycle time is determined during the wash cycle
by the water temperature, the amount of dishes, as well
as the degree of soiling and may vary (depending on the
selected wash cycle). You can change the time display
into time of day or hours/minutes so that the remaining
cycle time of the wash cycle appears in the display
window “Finish at” (for example 15:20 o’clock) or “Finish
in” (for example 3:25 hours).
Sensor setting
The wash cycle sequence is optimized in Auto wash
cycles with the aid of sensors. The sensors adjust the
wash cycle strength of Auto wash cycles depending on
the amount and type of soiling. You can adjust the
sensitivity of the sensors in 3 stages.
Standard:
This setting is recommend for daily regular or
typical use. This is the most energy efficient setting.
Sensitive:
This setting adjusts the wash cycle strength
for the effective removal of food remnants, even if the
amount of soiling is low. The energy and water
consumption is increased accordingly.
Very sensitive
:
This setting adjusts the wash cycle
strength for difficult conditions of use, for example firmly
dried on food remnants. This setting is recommended if
using biological or eco detergents which contain lower
amounts of active agents. The energy and water
consumption is increased accordingly.
Extra Dry
The final rinse uses a higher temperature which improves
the drying result. The cycle time may increase slightly.
(Caution if utensils are delicate!) You can switch the Extra
Dry function on or off. There is a slight increase in energy
consumption.
Summary of Contents for DWHD860RFM
Page 1: ...Use and care G U I D E THERMADOR COM Dishwasher DWHD860RPR DWHD860RFP DWHD860RFM...
Page 2: ...cm...
Page 8: ...8 Getting Started Appliance overview 67 57 UHVHW VHF VHF K PLQ UHVHW VHF VHF W...
Page 46: ...46 Mise en marche Vue d ensemble de l appareil 67 57 UHVHW VHF VHF K PLQ UHVHW VHF VHF W...
