Thermaco Big Dipper W-750-IS Installation & Operation Instructions Download Page 16

Page: 16 / 17

Thermaco, Inc. • 646 Greensboro St. • Asheboro, N. C. 27204-2548 • Phone (336) 629-4651

MNL-ISCU40000 16

40000 Series

Big Dipper

IS System Replacement Parts

Big Dipper

IS System Replacement Parts

EMPTY INTO

COOKING OIL

RECYCLING

CONTAINER

DAILY

SOLIDS STRAINER BASKET

FOR MODEL#

USE PART#

W-750-IS AND W-1250-IS

ST-97

GREASE/OILS COLLECTION CONTAINER*

FOR MODEL W-750-IS, USE PART# GC-7

FOR MODEL W-1250-IS, USE PART# GC-6 (2)

*Note:

W-750-IS system requires one (1)

W-1250-IS system requires two (2)

NOT SHOWN:

MOTOR*

PART# M-58

M-58-230 (For 230 VAC Units)

HEATER*

PART# H-8

H-8-230 (For 230 VAC Units)

INTERNAL FLOW CONTROL

(1 per unit)

PART# MFC-75 FOR W-750-IS

PART# MFC-125 FOR W-1250-IS

LID GASKET

PART# RG-7

WHEEL WIPER ASSEMBLY*

PART# WWA-4

WHEEL DRIVE SPROCKET*

PART# WDS-3

SKIMMING WHEEL ASSEMBLY*

PART# PDA-3

SAFETY SWITCH

PART# MSS-7

HEATER GASKET

PART# HTG-300

USER INTERFACE (Under Cover)

FOR ALL MODELS USE PART# PCBA-2

(INCLUDES USER INTERFACE, RIBBON CABLE,

PRINTED CIRCUIT BOARD AND THERMISTOR)

Summary of Contents for Big Dipper W-750-IS


















Search results

Summary of Contents for Big Dipper W-750-IS

Reviews:

Related manuals for Big Dipper W-750-IS

Brands by name

Popular brands

Thermaco Big Dipper W-750-IS, Installation & Operation Instructions

Search results

Summary of Contents for Big Dipper W-750-IS

Reviews:

Related manuals for Big Dipper W-750-IS

Brands by name

Popular brands